Poulan 96192002901, 428689 Maintenance, General Recommendations, Before Each USE, Lubrication

Page 13

MAINTENANCE

GENERAL RECOMMENDATIONS

The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain snow thrower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your snow thrower. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season.

•Once a year, you should replace the spark plug and check belts for wear. A new spark plug will help your engine run better and last longer.

•Follow the maintenance schedule in this manual.

NOTE: Use only Original Equipment Manufacturer (OEM) parts to service this unit. Failure to do so can cause the unit to malfunction and pose a risk of injury to the operator.

BEFORE EACH USE

1.Check engine oil level.

2.Check for loose fasteners.

3.Check controls to be sure they are functioning properly.

LUBRICATION

Keep your snow thrower well lubricated (See “LUBRICATION CHART”).

SNOW THROWER

LUBRICATION CHART

SAE 5W-30 Motor Oil

See “ENGINE”

in Maintenance section

General

Purpose

Grease

Pivot points

Auger

 

grease fittings

Engine oil

 

Always observe the safety rules when performing any

BELTS

maintenance.

Check belts for deterioration and wear after every 50 hours

TIRES

of operation and replace if necessary. The belts are not

adjustable. Replace belts if they begin to slip from wear.

• Maintain proper air pressure in both tires (14–17 P.S.I).

(See “TO REMOVE BELT COVER” in the Service and

• Keep tires free of gasoline and oil, which can harm

Adjustments section of this manual).

rubber.

The belts on your snow thrower are of special construction

NOTE: To seal tire punctures and prevent flat tires due

and should be replaced by original equipment manufacturer

to slow leaks, tire sealant may be purchased from your

(OEM) belts available from your nearest dealer. Using other

local parts dealer. Tire sealant also prevents tire dry rot

than OEM belts can cause personal injury or damage to

and corrosion.

13 the snow thrower.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenSnow Thrower Lubrication Chart MaintenanceGeneral Recommendations Before Each USEEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsSnow Thrower Chute DeflectorTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting KEY Part Description Auger HousingScraper BAR Auger BearingAuger Assembly RH Auger Assembly LHSkid Plate LH Skid Plate RHExploded 178675X008 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller PulleyCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadDeflector Weldment Chute WeldmentDeflector Seal StrapRepair Parts Snow Thrower - Model NO. PR624ES Handles Pivot Support Lower TubeInterlock Spring Interlock CAMKnob RED SpacerHandle Knob Washer 3/8Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomRepair Parts Snow Thrower - Model NO. PR624ES Drive Speed Selector Roll PIN 3/16 Axle ShaftSprocket Clik PINComplete LCT Engine Cover AssemblyFrame 427963X428Traction Belt Impeller BeltIdler ARM Bracket Idler PulleyWheel Assembly LH Repair Parts Snow Thrower - Model NO. PR624ES WheelsSafety Ignition KEY Repair Parts BAG of Parts422663 181037 Repair Parts Snow Thrower - Model NO. PR624ES DecalsDECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

96192002901, 428689 specifications

The Poulan 428689, 96192002901 is a high-quality replacement part designed to enhance the performance of various Poulan outdoor power equipment. It is primarily recognized for its durability and compatibility with a range of Poulan chainsaws, trimmers, and blowers, making it an essential component for those who rely on these tools for their landscaping and gardening needs.

One of the main features of the Poulan 428689 is its robust construction. Made from high-grade materials, this replacement part ensures longevity and exceptional performance under demanding conditions. It can withstand the rigors of heavy use, whether you are trimming hedges, cutting firewood, or clearing debris, making it a reliable choice for both casual users and professionals alike.

The technology incorporated into the Poulan 428689 focuses on ease of installation and user-friendly operation. Designed for compatibility with many Poulan models, this replacement part can be installed with minimal effort, allowing users to quickly get their equipment back in top working condition. This accessibility is a boon for those who may not have extensive mechanical experience, enabling a hassle-free replacement process.

In terms of characteristics, the Poulan 428689 is engineered to fit seamlessly into your existing power tools, ensuring optimal performance. Its precision manufacturing allows it to meet or exceed original equipment specifications, maintaining the efficiency and speed necessary for effective operation. This aspect is particularly crucial for tasks that demand precision and power, such as pruning trees or performing detailed landscaping tasks.

Another notable characteristic of the Poulan 428689 is its lightweight design, which contributes to the overall maneuverability of the equipment. Users can work for extended periods without experiencing undue fatigue, making it a favorite among professionals who spend long hours in the field.

In conclusion, the Poulan 428689, 96192002901 is a vital component for anyone seeking to maintain or enhance the performance of their Poulan outdoor equipment. Its durable construction, ease of installation, superior compatibility, and lightweight design set it apart as a leading choice for maintaining your tools in optimum working condition. Whether you're a weekend gardener or a seasoned landscaper, this replacement part will not only enhance your equipment's performance but also ensure that you can tackle any landscaping challenge that comes your way.
Top Page Image Contents