Poulan 428689, 96192002901 owner manual Storage, Other, Fuel System, Engine OIL, Cylinder

Page 18

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenGeneral Recommendations MaintenanceSnow Thrower Lubrication Chart Before Each USECleaning EngineSnow Thrower Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Scraper BAR Auger HousingKEY Part Description Auger BearingSkid Plate LH Auger Assembly LHAuger Assembly RH Skid Plate RHExploded Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller PulleyCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadDeflector Seal Chute WeldmentDeflector Weldment StrapRepair Parts Snow Thrower - Model NO. PR624ES Handles Interlock Spring Lower TubePivot Support Interlock CAMHandle Knob SpacerKnob RED Washer 3/8Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomRepair Parts Snow Thrower - Model NO. PR624ES Drive Speed Selector Sprocket Axle ShaftRoll PIN 3/16 Clik PINFrame Cover AssemblyComplete LCT Engine 427963X428Idler ARM Bracket Impeller BeltTraction Belt Idler PulleyRepair Parts Snow Thrower - Model NO. PR624ES Wheels Wheel Assembly LHRepair Parts BAG of Parts Safety Ignition KEY422663 DECAL, Danger Repair Parts Snow Thrower - Model NO. PR624ES Decals181037 DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

96192002901, 428689 specifications

The Poulan 428689, 96192002901 is a high-quality replacement part designed to enhance the performance of various Poulan outdoor power equipment. It is primarily recognized for its durability and compatibility with a range of Poulan chainsaws, trimmers, and blowers, making it an essential component for those who rely on these tools for their landscaping and gardening needs.

One of the main features of the Poulan 428689 is its robust construction. Made from high-grade materials, this replacement part ensures longevity and exceptional performance under demanding conditions. It can withstand the rigors of heavy use, whether you are trimming hedges, cutting firewood, or clearing debris, making it a reliable choice for both casual users and professionals alike.

The technology incorporated into the Poulan 428689 focuses on ease of installation and user-friendly operation. Designed for compatibility with many Poulan models, this replacement part can be installed with minimal effort, allowing users to quickly get their equipment back in top working condition. This accessibility is a boon for those who may not have extensive mechanical experience, enabling a hassle-free replacement process.

In terms of characteristics, the Poulan 428689 is engineered to fit seamlessly into your existing power tools, ensuring optimal performance. Its precision manufacturing allows it to meet or exceed original equipment specifications, maintaining the efficiency and speed necessary for effective operation. This aspect is particularly crucial for tasks that demand precision and power, such as pruning trees or performing detailed landscaping tasks.

Another notable characteristic of the Poulan 428689 is its lightweight design, which contributes to the overall maneuverability of the equipment. Users can work for extended periods without experiencing undue fatigue, making it a favorite among professionals who spend long hours in the field.

In conclusion, the Poulan 428689, 96192002901 is a vital component for anyone seeking to maintain or enhance the performance of their Poulan outdoor equipment. Its durable construction, ease of installation, superior compatibility, and lightweight design set it apart as a leading choice for maintaining your tools in optimum working condition. Whether you're a weekend gardener or a seasoned landscaper, this replacement part will not only enhance your equipment's performance but also ensure that you can tackle any landscaping challenge that comes your way.
Top Page Image Contents