Poulan 96192002901, 428689 To Remove Wheels See Fig, To Adjust Cable Tension See Fig, Carburetor

Page 17

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 21)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 21

TO ADJUST CABLE TENSION (See Fig. 22)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 22

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenSnow Thrower Lubrication Chart MaintenanceGeneral Recommendations Before Each USEEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsSnow Thrower Chute DeflectorTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting KEY Part Description Auger HousingScraper BAR Auger BearingAuger Assembly RH Auger Assembly LHSkid Plate LH Skid Plate RHExploded 178675X008 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller PulleyCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadDeflector Weldment Chute WeldmentDeflector Seal StrapRepair Parts Snow Thrower - Model NO. PR624ES Handles Pivot Support Lower TubeInterlock Spring Interlock CAMKnob RED SpacerHandle Knob Washer 3/8Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomRepair Parts Snow Thrower - Model NO. PR624ES Drive Speed Selector Roll PIN 3/16 Axle ShaftSprocket Clik PINComplete LCT Engine Cover AssemblyFrame 427963X428Traction Belt Impeller BeltIdler ARM Bracket Idler PulleyWheel Assembly LH Repair Parts Snow Thrower - Model NO. PR624ES Wheels422663 Repair Parts BAG of PartsSafety Ignition KEY 181037 Repair Parts Snow Thrower - Model NO. PR624ES DecalsDECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

96192002901, 428689 specifications

The Poulan 428689, 96192002901 is a high-quality replacement part designed to enhance the performance of various Poulan outdoor power equipment. It is primarily recognized for its durability and compatibility with a range of Poulan chainsaws, trimmers, and blowers, making it an essential component for those who rely on these tools for their landscaping and gardening needs.

One of the main features of the Poulan 428689 is its robust construction. Made from high-grade materials, this replacement part ensures longevity and exceptional performance under demanding conditions. It can withstand the rigors of heavy use, whether you are trimming hedges, cutting firewood, or clearing debris, making it a reliable choice for both casual users and professionals alike.

The technology incorporated into the Poulan 428689 focuses on ease of installation and user-friendly operation. Designed for compatibility with many Poulan models, this replacement part can be installed with minimal effort, allowing users to quickly get their equipment back in top working condition. This accessibility is a boon for those who may not have extensive mechanical experience, enabling a hassle-free replacement process.

In terms of characteristics, the Poulan 428689 is engineered to fit seamlessly into your existing power tools, ensuring optimal performance. Its precision manufacturing allows it to meet or exceed original equipment specifications, maintaining the efficiency and speed necessary for effective operation. This aspect is particularly crucial for tasks that demand precision and power, such as pruning trees or performing detailed landscaping tasks.

Another notable characteristic of the Poulan 428689 is its lightweight design, which contributes to the overall maneuverability of the equipment. Users can work for extended periods without experiencing undue fatigue, making it a favorite among professionals who spend long hours in the field.

In conclusion, the Poulan 428689, 96192002901 is a vital component for anyone seeking to maintain or enhance the performance of their Poulan outdoor equipment. Its durable construction, ease of installation, superior compatibility, and lightweight design set it apart as a leading choice for maintaining your tools in optimum working condition. Whether you're a weekend gardener or a seasoned landscaper, this replacement part will not only enhance your equipment's performance but also ensure that you can tackle any landscaping challenge that comes your way.
Top Page Image Contents