Poulan 96192002901 HOW to USE Your Snow Thrower, Stopping, To USE Fuel SHUT-OFF Valve See Fig

Page 9

OPERATION

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear

safety glasses or eye shields while operating 00155 your snow thrower or performing any adjust- ments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

•Release the auger control lever to stop throwing snow.

ENGINE

1.Move ON / OFF switch to “OFF” position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE FUEL SHUT-OFF VALVE (See Fig. 9)

The fuel shut-off valve is located beneath the fuel tank on the engine. Always operate the snow thrower with the fuel shut-off valve in the OPEN position.

OFF

OPEN

FIG. 9

TO USE CHOKE CONTROL (See Fig. 10)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

•To engage choke, rotate lever to “FULL” position.

FULL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FIG. 10

9

TO CONTROL SNOW DISCHARGE (See Figs. 11 & 12)

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

WARNING: If the discharge chute or auger become clogged, shut-off engine and waitfor all moving parts to stop. Use the clean-out tool, NOT YOUR HANDS, to unclog the chute and/or auger.

The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever.

•To change the discharge chute position, press down- ward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROL LEVER

FIG. 11

The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther.

•To change the deflector position, loosen knob, move de- flector to desired position and tighten knob securely.

HIGH

POSITION

KNOB

CHUTE

DEFLECTOR

LOW POSITION

FIG. 12

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenSnow Thrower Lubrication Chart MaintenanceGeneral Recommendations Before Each USEEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsSnow Thrower Chute DeflectorTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting KEY Part Description Auger HousingScraper BAR Auger BearingAuger Assembly RH Auger Assembly LHSkid Plate LH Skid Plate RHExploded 178675X008 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller PulleyCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadDeflector Weldment Chute WeldmentDeflector Seal StrapRepair Parts Snow Thrower - Model NO. PR624ES Handles Pivot Support Lower TubeInterlock Spring Interlock CAMKnob RED SpacerHandle Knob Washer 3/8Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomRepair Parts Snow Thrower - Model NO. PR624ES Drive Speed Selector Roll PIN 3/16 Axle ShaftSprocket Clik PINComplete LCT Engine Cover AssemblyFrame 427963X428Traction Belt Impeller BeltIdler ARM Bracket Idler PulleyWheel Assembly LH Repair Parts Snow Thrower - Model NO. PR624ES WheelsRepair Parts BAG of Parts Safety Ignition KEY422663 181037 Repair Parts Snow Thrower - Model NO. PR624ES DecalsDECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

96192002901, 428689 specifications

The Poulan 428689, 96192002901 is a high-quality replacement part designed to enhance the performance of various Poulan outdoor power equipment. It is primarily recognized for its durability and compatibility with a range of Poulan chainsaws, trimmers, and blowers, making it an essential component for those who rely on these tools for their landscaping and gardening needs.

One of the main features of the Poulan 428689 is its robust construction. Made from high-grade materials, this replacement part ensures longevity and exceptional performance under demanding conditions. It can withstand the rigors of heavy use, whether you are trimming hedges, cutting firewood, or clearing debris, making it a reliable choice for both casual users and professionals alike.

The technology incorporated into the Poulan 428689 focuses on ease of installation and user-friendly operation. Designed for compatibility with many Poulan models, this replacement part can be installed with minimal effort, allowing users to quickly get their equipment back in top working condition. This accessibility is a boon for those who may not have extensive mechanical experience, enabling a hassle-free replacement process.

In terms of characteristics, the Poulan 428689 is engineered to fit seamlessly into your existing power tools, ensuring optimal performance. Its precision manufacturing allows it to meet or exceed original equipment specifications, maintaining the efficiency and speed necessary for effective operation. This aspect is particularly crucial for tasks that demand precision and power, such as pruning trees or performing detailed landscaping tasks.

Another notable characteristic of the Poulan 428689 is its lightweight design, which contributes to the overall maneuverability of the equipment. Users can work for extended periods without experiencing undue fatigue, making it a favorite among professionals who spend long hours in the field.

In conclusion, the Poulan 428689, 96192002901 is a vital component for anyone seeking to maintain or enhance the performance of their Poulan outdoor equipment. Its durable construction, ease of installation, superior compatibility, and lightweight design set it apart as a leading choice for maintaining your tools in optimum working condition. Whether you're a weekend gardener or a seasoned landscaper, this replacement part will not only enhance your equipment's performance but also ensure that you can tackle any landscaping challenge that comes your way.
Top Page Image Contents