Poulan 96192002901, 428689 owner manual Troubleshooting

Page 19

TROUBLESHOOTING

See appropriate section in manual unless directed to an authorized service center/department.

PROBLEM

 

CAUSE

 

CORRECTION

Does not start

1.

Fuel shut-off valve (if so

1.

Turn fuel shut-off valve to OPEN position.

 

 

equipped) in OFF position.

 

 

 

2.

Safety ignition key

2.

Insert safety ignition key.

 

 

is not inserted.

 

 

 

3.

Out of fuel.

3.

Fill fuel tank with fresh, clean gasoline.

 

4.

Throttle in STOP position

4.

Move throttle to FAST position

 

 

(or ON/OFF switch is OFF).

 

(or ON/OFF switch to ON position).

 

5.

Choke in OFF position.

5.

Move to FULL position.

 

6.

Primer not depressed.

6.

Prime as instructed in the Operation section of this manual.

 

7.

Engine is flooded.

7.

Wait a few minutes before restarting, DO NOT prime.

 

8.

Spark plug wire is

8.

Connect wire to spark plug.

 

 

disconnected.

 

 

 

9.

Bad spark plug.

9.

Replace spark plug.

 

10.

Stale fuel.

10.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

11.

Water in fuel.

11.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Reconnect spark plug wire.

 

2.

Throwing too much snow.

2.

Reduce speed and width of swath.

 

3.

Fuel tank cap is covered

3.

Remove ice and snow on and around fuel tank cap.

 

 

with ice or snow.

 

 

 

4.

Dirty or clogged muffler.

4.

Clean or replace muffler.

 

 

 

 

 

Engine idles or

1.

Choke is in FULL position.

1.

Move choke to OFF position.

runs roughly

2.

Blockage in fuel line.

2.

Clean fuel line.

 

3.

Stale fuel.

3.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

4.

Water in fuel.

4.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

5.

Carburetor is in need of

5.

Contact an authorized service center/department.

 

 

adjustment or overhaul.

 

 

 

 

 

 

 

Excessive

1.

Loose parts or damaged

1.

Tighten all fasteners. Replace damaged parts. If vibration

vibration

 

augers or impeller.

 

remains, contact an authorized service center/department.

 

 

 

 

 

Recoil starter

1.

Frozen recoil starter.

1.

See “IF RECOIL STARTER HAS FROZEN”

is hard to pull

 

 

 

in the Operation section of this manual.

 

 

 

 

 

Loss of traction

1.

Drive belt is worn.

1.

Check / replace drive belt.

drive / slowing

2.

Drive belt is off of pulley.

2.

Check / reinstall drive belt.

of drive speed

3.

Friction drive wheel is worn.

3.

Contact an authorized service center/department.

 

 

 

 

 

Loss of snow

1.

Auger belt is off of pulley.

1.

Check / reinstall auger belt.

discharge or

2.

Auger belt is worn.

2.

Check / replace auger belt.

slowing of

3.

Clogged discharge chute.

3.

Clean snow chute.

snow discharge

4.

Augers / impeller jammed.

4.

Remove debris or foreign object from augers / impeller.

 

 

 

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingBefore Each USE MaintenanceSnow Thrower Lubrication Chart General RecommendationsEngine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Snow ThrowerTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Auger Bearing Auger HousingKEY Part Description Scraper BARSkid Plate RH Auger Assembly LHAuger Assembly RH Skid Plate LHExploded Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool BearingRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldStrap Chute WeldmentDeflector Weldment Deflector SealRepair Parts Snow Thrower - Model NO. PR624ES Handles Interlock CAM Lower TubePivot Support Interlock SpringWasher 3/8 SpacerKnob RED Handle KnobShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPRepair Parts Snow Thrower - Model NO. PR624ES Drive Speed Selector Clik PIN Axle ShaftRoll PIN 3/16 Sprocket427963X428 Cover AssemblyComplete LCT Engine FrameIdler Pulley Impeller BeltTraction Belt Idler ARM BracketWheel Assembly LH Repair Parts Snow Thrower - Model NO. PR624ES WheelsSafety Ignition KEY Repair Parts BAG of Parts422663 DECAL, DANGER, Deflector Repair Parts Snow Thrower - Model NO. PR624ES Decals181037 DECAL, DangerService Notes Service Notes Limited Warranty

96192002901, 428689 specifications

The Poulan 428689, 96192002901 is a high-quality replacement part designed to enhance the performance of various Poulan outdoor power equipment. It is primarily recognized for its durability and compatibility with a range of Poulan chainsaws, trimmers, and blowers, making it an essential component for those who rely on these tools for their landscaping and gardening needs.

One of the main features of the Poulan 428689 is its robust construction. Made from high-grade materials, this replacement part ensures longevity and exceptional performance under demanding conditions. It can withstand the rigors of heavy use, whether you are trimming hedges, cutting firewood, or clearing debris, making it a reliable choice for both casual users and professionals alike.

The technology incorporated into the Poulan 428689 focuses on ease of installation and user-friendly operation. Designed for compatibility with many Poulan models, this replacement part can be installed with minimal effort, allowing users to quickly get their equipment back in top working condition. This accessibility is a boon for those who may not have extensive mechanical experience, enabling a hassle-free replacement process.

In terms of characteristics, the Poulan 428689 is engineered to fit seamlessly into your existing power tools, ensuring optimal performance. Its precision manufacturing allows it to meet or exceed original equipment specifications, maintaining the efficiency and speed necessary for effective operation. This aspect is particularly crucial for tasks that demand precision and power, such as pruning trees or performing detailed landscaping tasks.

Another notable characteristic of the Poulan 428689 is its lightweight design, which contributes to the overall maneuverability of the equipment. Users can work for extended periods without experiencing undue fatigue, making it a favorite among professionals who spend long hours in the field.

In conclusion, the Poulan 428689, 96192002901 is a vital component for anyone seeking to maintain or enhance the performance of their Poulan outdoor equipment. Its durable construction, ease of installation, superior compatibility, and lightweight design set it apart as a leading choice for maintaining your tools in optimum working condition. Whether you're a weekend gardener or a seasoned landscaper, this replacement part will not only enhance your equipment's performance but also ensure that you can tackle any landscaping challenge that comes your way.
Top Page Image Contents