Poulan 428550, 96198002800, PP265E27 owner manual Before Starting the Engine, To Start Engine

Page 12

OPERATION

TO ADJUST SKID PLATES (See Fig. 18)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the hex nuts, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

ADD GASOLINE (See Fig. 19)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract mois- ture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

HIGH POSITION

 

(LOW GROUND

 

CLEARANCE)

 

 

AUGER

 

HOUSING

 

SCRAPER BAR

HEX

SKID PLATE

NUTS

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 18

SCRAPER BAR (See Fig. 18)

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn

PRIMER

CHOKE

CONTROL

SAFETY

IGNITION KEY

FUEL SHUT-OFF

VALVE

ENGINE OIL FILL CAP / DIPSTICK

POWER

CORD

PLUG

RECOIL

(AUXILIARY)

STARTER HANDLE

THROTTLE

almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 19)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 19

TO START ENGINE

•Be sure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Seri- ous personal injury or damage to your snow thrower could result.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine To Start EngineSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Auger Housing KEY Part DescriptionScraper BAR Auger 27 LH23 22 KEY Part NO. NO. Description Auger Bearing Bearing PlugDeflector Control Assembly Deflector Spring 15 420679 Service Part Deflector ControlChute Weldment Deflector WeldmentLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadLoop Handle LH Loop Handle RHLower Tube Pivot SupportSpacer RetainerKnob RED Handle KnobImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomWire Harness Console PanelHeadlight Bezel Flood HeadlightAxle Shaft Roll PIN 3/16Sprocket Clik PINExploded Assembly Drive Plate AssemblySpeed Selector Rubber RingCover Assembly Frame427963X428 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler PulleyWheel Assembly LH 187833X421187865X421 Power Cord Retainer PINWrench Remote Spring181037 DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionKEY Part Description QTY Warranty MANUFACTURER’S Warranty CoverageII. Emission Control System Warranty Warranty Limited Warranty

PP265E27, 96198002800, 428550 specifications

The Poulan 428550, also known as the PP265E27, is a robust and versatile trimmer designed for both residential and professional use. This model stands out due to its exceptional combination of power, lightweight design, and user-friendly features, making it an excellent choice for anyone looking to maintain their lawn and garden effectively.

One of the main features of the Poulan 428550 is its reliable 25cc 2-cycle engine. This powerful engine provides a significant amount of torque, enabling users to cut through thick grass, weeds, and even light brush with ease. The engine’s design prioritizes efficiency and durability, ensuring that it can handle a variety of trimming tasks without compromising performance.

The lightweight construction of the PP265E27 is another significant advantage. Weighing in at approximately 10 pounds, this trimmer is easy to maneuver, reducing user fatigue during extended periods of use. The adjustable handle allows for ergonomic positioning, making it comfortable for users of different heights and helping to reduce strain on the back and arms.

One of the standout technologies in the Poulan 428550 is its Smart Start feature. This innovative technology is designed to make starting the engine as easy as possible. It reduces the resistance in the starting cord by 30%, allowing even novice users to start the trimmer with minimal effort. This feature is especially valuable for those who may struggle with traditional pull-start engines.

Another characteristic of the PP265E27 is its dual-line cutting system. This system includes a 17-inch cutting width, which allows for efficient trimming of larger areas in less time. The trimmer uses a bump feed mechanism, enabling users to quickly advance the line as needed without stopping work. This ensures that users can maintain their momentum while tackling their yard maintenance tasks.

Durability is an essential factor in the design of the Poulan 428550. Its sturdy construction and high-quality materials ensure that it can withstand the rigors of regular use. Additionally, its low-vibration design helps to minimize fatigue, making it suitable for extended use without discomfort.

In summary, the Poulan 428550, or PP265E27, is a highly efficient and user-friendly trimmer that combines power, lightweight construction, and innovative features. Whether for residential or occasional professional use, this model provides reliability and effectiveness, making it a valuable addition to any lawn care toolkit. Its combination of a powerful engine, ergonomic design, and advanced technology ensures that users can tackle their trimming tasks with ease and efficiency.
Top Page Image Contents