Poulan 96198002800, 428550, PP265E27 owner manual Storage, Other, Fuel System, Engine OIL, Cylinder

Page 19

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Alcohol blended fuels (called gasohol or using ethanol or metha- nol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can dam- age the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour approximately one ounce (30 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Start Engine Before Starting the EngineBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Auger 27 LH Auger HousingKEY Part Description Scraper BAR23 22 KEY Part NO. NO. Description Bearing Plug Auger BearingDeflector Weldment Deflector Control AssemblyDeflector Spring 15 420679 Service Part Deflector Control Chute WeldmentRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldPivot Support Loop Handle LHLoop Handle RH Lower TubeHandle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPFlood Headlight Wire HarnessConsole Panel Headlight BezelClik PIN Axle ShaftRoll PIN 3/16 SprocketExploded Rubber Ring AssemblyDrive Plate Assembly Speed SelectorEngine Mounting Plate Cover AssemblyFrame 427963X428Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket187833X421 Wheel Assembly LH187865X421 Remote Spring Power CordRetainer PIN WrenchDECAL, Instruction 181037DECAL, Danger DECAL, DANGER, DeflectorKEY Part Description QTY MANUFACTURER’S Warranty Coverage WarrantyII. Emission Control System Warranty Warranty Limited Warranty

PP265E27, 96198002800, 428550 specifications

The Poulan 428550, also known as the PP265E27, is a robust and versatile trimmer designed for both residential and professional use. This model stands out due to its exceptional combination of power, lightweight design, and user-friendly features, making it an excellent choice for anyone looking to maintain their lawn and garden effectively.

One of the main features of the Poulan 428550 is its reliable 25cc 2-cycle engine. This powerful engine provides a significant amount of torque, enabling users to cut through thick grass, weeds, and even light brush with ease. The engine’s design prioritizes efficiency and durability, ensuring that it can handle a variety of trimming tasks without compromising performance.

The lightweight construction of the PP265E27 is another significant advantage. Weighing in at approximately 10 pounds, this trimmer is easy to maneuver, reducing user fatigue during extended periods of use. The adjustable handle allows for ergonomic positioning, making it comfortable for users of different heights and helping to reduce strain on the back and arms.

One of the standout technologies in the Poulan 428550 is its Smart Start feature. This innovative technology is designed to make starting the engine as easy as possible. It reduces the resistance in the starting cord by 30%, allowing even novice users to start the trimmer with minimal effort. This feature is especially valuable for those who may struggle with traditional pull-start engines.

Another characteristic of the PP265E27 is its dual-line cutting system. This system includes a 17-inch cutting width, which allows for efficient trimming of larger areas in less time. The trimmer uses a bump feed mechanism, enabling users to quickly advance the line as needed without stopping work. This ensures that users can maintain their momentum while tackling their yard maintenance tasks.

Durability is an essential factor in the design of the Poulan 428550. Its sturdy construction and high-quality materials ensure that it can withstand the rigors of regular use. Additionally, its low-vibration design helps to minimize fatigue, making it suitable for extended use without discomfort.

In summary, the Poulan 428550, or PP265E27, is a highly efficient and user-friendly trimmer that combines power, lightweight construction, and innovative features. Whether for residential or occasional professional use, this model provides reliability and effectiveness, making it a valuable addition to any lawn care toolkit. Its combination of a powerful engine, ergonomic design, and advanced technology ensures that users can tackle their trimming tasks with ease and efficiency.
Top Page Image Contents