Poulan 428550, 96198002800, PP265E27 owner manual Engine, Cleaning

Page 15

MAINTENANCE

BELTS

Check belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual).

The belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F/0°C. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug and place wire where it can- not come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig To Start Engine Before Starting the EngineSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Auger 27 LH Auger HousingKEY Part Description Scraper BAR23 22 KEY Part NO. NO. Description Bearing Plug Auger BearingDeflector Weldment Deflector Control AssemblyDeflector Spring 15 420679 Service Part Deflector Control Chute WeldmentRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldPivot Support Loop Handle LHLoop Handle RH Lower TubeHandle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPFlood Headlight Wire HarnessConsole Panel Headlight BezelClik PIN Axle ShaftRoll PIN 3/16 SprocketExploded Rubber Ring AssemblyDrive Plate Assembly Speed SelectorEngine Mounting Plate Cover AssemblyFrame 427963X428Idler Pulley Impeller BeltTraction Belt Idler ARM BracketWheel Assembly LH 187833X421187865X421 Remote Spring Power CordRetainer PIN WrenchDECAL, Instruction 181037DECAL, Danger DECAL, DANGER, DeflectorKEY Part Description QTY MANUFACTURER’S Warranty Coverage WarrantyII. Emission Control System Warranty Warranty Limited Warranty

PP265E27, 96198002800, 428550 specifications

The Poulan 428550, also known as the PP265E27, is a robust and versatile trimmer designed for both residential and professional use. This model stands out due to its exceptional combination of power, lightweight design, and user-friendly features, making it an excellent choice for anyone looking to maintain their lawn and garden effectively.

One of the main features of the Poulan 428550 is its reliable 25cc 2-cycle engine. This powerful engine provides a significant amount of torque, enabling users to cut through thick grass, weeds, and even light brush with ease. The engine’s design prioritizes efficiency and durability, ensuring that it can handle a variety of trimming tasks without compromising performance.

The lightweight construction of the PP265E27 is another significant advantage. Weighing in at approximately 10 pounds, this trimmer is easy to maneuver, reducing user fatigue during extended periods of use. The adjustable handle allows for ergonomic positioning, making it comfortable for users of different heights and helping to reduce strain on the back and arms.

One of the standout technologies in the Poulan 428550 is its Smart Start feature. This innovative technology is designed to make starting the engine as easy as possible. It reduces the resistance in the starting cord by 30%, allowing even novice users to start the trimmer with minimal effort. This feature is especially valuable for those who may struggle with traditional pull-start engines.

Another characteristic of the PP265E27 is its dual-line cutting system. This system includes a 17-inch cutting width, which allows for efficient trimming of larger areas in less time. The trimmer uses a bump feed mechanism, enabling users to quickly advance the line as needed without stopping work. This ensures that users can maintain their momentum while tackling their yard maintenance tasks.

Durability is an essential factor in the design of the Poulan 428550. Its sturdy construction and high-quality materials ensure that it can withstand the rigors of regular use. Additionally, its low-vibration design helps to minimize fatigue, making it suitable for extended use without discomfort.

In summary, the Poulan 428550, or PP265E27, is a highly efficient and user-friendly trimmer that combines power, lightweight construction, and innovative features. Whether for residential or occasional professional use, this model provides reliability and effectiveness, making it a valuable addition to any lawn care toolkit. Its combination of a powerful engine, ergonomic design, and advanced technology ensures that users can tackle their trimming tasks with ease and efficiency.
Top Page Image Contents