Poulan 96198002800, 428550 Snow Throwing Tips, Before Stopping, If Recoil Starter has Frozen

Page 13

OPERATION

COLD START - ELECTRIC STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place throttle control in “FAST” position.

3.Rotate choke control to “FULL” position.

4.Connect the power cord to the engine.

5.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

NOTE: Do not use primer when starting engine with the electric starter.

6. Push starter button until engine starts.

IMPORTANT: Do not crank engine more than five continu- ous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt.

7.When the engine starts, release the starter button and slowly move the choke control to the “OFF” position.

8.Disconnect the power cord from the receptacle first, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the “OFF” position.

COLD START - RECOIL STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place throttle control in “FAST” position.

3.Rotate choke control to “FULL” position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” posi- tion.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

•Always operate the snow thrower with the engine at full throttle. Full throttle offers the best performance.

•Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the throttle, to adjust speed.

•It is easier and more efficient to remove snow imme- diately after it falls.

•The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

•Slightly overlap each successive path to ensure all snow will be removed.

•Throw snow downwind whenever possible.

•Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

•For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

•Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

•After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

•Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Start Engine Before Starting the EngineBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting KEY Part Description Auger HousingScraper BAR Auger 27 LH23 22 KEY Part NO. NO. Description Bearing Plug Auger BearingDeflector Spring 15 420679 Service Part Deflector Control Deflector Control AssemblyChute Weldment Deflector WeldmentCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadLoop Handle RH Loop Handle LHLower Tube Pivot SupportRetainer SpacerKnob RED Handle KnobTraction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomConsole Panel Wire HarnessHeadlight Bezel Flood HeadlightRoll PIN 3/16 Axle ShaftSprocket Clik PINExploded Drive Plate Assembly AssemblySpeed Selector Rubber RingFrame Cover Assembly427963X428 Engine Mounting PlateTraction Belt Impeller BeltIdler ARM Bracket Idler Pulley187833X421 Wheel Assembly LH187865X421 Retainer PIN Power CordWrench Remote SpringDECAL, Danger 181037DECAL, DANGER, Deflector DECAL, InstructionKEY Part Description QTY MANUFACTURER’S Warranty Coverage WarrantyII. Emission Control System Warranty Warranty Limited Warranty

PP265E27, 96198002800, 428550 specifications

The Poulan 428550, also known as the PP265E27, is a robust and versatile trimmer designed for both residential and professional use. This model stands out due to its exceptional combination of power, lightweight design, and user-friendly features, making it an excellent choice for anyone looking to maintain their lawn and garden effectively.

One of the main features of the Poulan 428550 is its reliable 25cc 2-cycle engine. This powerful engine provides a significant amount of torque, enabling users to cut through thick grass, weeds, and even light brush with ease. The engine’s design prioritizes efficiency and durability, ensuring that it can handle a variety of trimming tasks without compromising performance.

The lightweight construction of the PP265E27 is another significant advantage. Weighing in at approximately 10 pounds, this trimmer is easy to maneuver, reducing user fatigue during extended periods of use. The adjustable handle allows for ergonomic positioning, making it comfortable for users of different heights and helping to reduce strain on the back and arms.

One of the standout technologies in the Poulan 428550 is its Smart Start feature. This innovative technology is designed to make starting the engine as easy as possible. It reduces the resistance in the starting cord by 30%, allowing even novice users to start the trimmer with minimal effort. This feature is especially valuable for those who may struggle with traditional pull-start engines.

Another characteristic of the PP265E27 is its dual-line cutting system. This system includes a 17-inch cutting width, which allows for efficient trimming of larger areas in less time. The trimmer uses a bump feed mechanism, enabling users to quickly advance the line as needed without stopping work. This ensures that users can maintain their momentum while tackling their yard maintenance tasks.

Durability is an essential factor in the design of the Poulan 428550. Its sturdy construction and high-quality materials ensure that it can withstand the rigors of regular use. Additionally, its low-vibration design helps to minimize fatigue, making it suitable for extended use without discomfort.

In summary, the Poulan 428550, or PP265E27, is a highly efficient and user-friendly trimmer that combines power, lightweight construction, and innovative features. Whether for residential or occasional professional use, this model provides reliability and effectiveness, making it a valuable addition to any lawn care toolkit. Its combination of a powerful engine, ergonomic design, and advanced technology ensures that users can tackle their trimming tasks with ease and efficiency.
Top Page Image Contents