Poulan 96192002402, 422088 owner manual KEY Part Description

Page 21

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT1053ES (96192002402)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1175321X479 IMPELLER

2196710 GEARBOX ASSEMBLY

3	188909	BEARING
4	191079	IMPELLER PULLEY
5	175322	DISCHARGE BASE

6178675X008 CORNER BRACKET

7192199 CLEAN OUT TOOL

8	405400	TOOL CLIP
9	73800400	NUT 1/4−20
10	74780426	SCREW 1/4−20 X .625
11	155377	NUT 5/16−18

12163183 SCREW 5/16−18 X .625

1319111507 WASHER

1410040500 LOCKWASHER 5/16

1574940516 SCREW 5/16−18 X 1.00

16180355 CARRIAGE BOLT

17194189 SCREW 13−16 X .625

18	407760	PLUG
19	407761	GEARBOX COVER RH
20	407766	GASKET
21	407770	SEAL
22	407762	BEARING
23	174697	THRUST WASHER 1.00
24	407763	WORM GEAR
25	407764	AUGER SHAFT
26	189282	SQUARE KEY
27	407758	BEARING
28	174683	THRUST WASHER
29	407757	IMPELLER SHAFT
30	7836M	ROLL PIN
31	174681	THRUST WASHER
32	174684	THRUST BEARING
33	407769	BEARING
34	407768	O−RING

35407767 SCREW 5/16−18 X .750

36407765 GEARBOX COVER LH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 21

Image 21

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Scraper BAR Auger HousingCARRIAGEBOLT5/16−18X.625 Auger BearingAuger Assembly 30 RH Auger Assembly 30 LHChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley PivotLoop Handle RH Loop Handle LHLower Tube Pivot SupportRetainer SpacerKnob RED Handle KnobTraction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomConsole Panel Wire HarnessHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number XT1053ES Drive 43 402689 Drive Plate Assembly Speed Selector AssemblyEND Plate Washer01.03.002-A KEY Part Description ENGINE, TEC Model LH358SA-159628A423184X505 Engine Mount Plate Belt Cover Traction BeltImpeller Belt Cable Bracket RH Cable Bracket LHWheel Driver Retainer Ring CoverWheel Lobe Clutch Slide35062 Safety Ignition KEY181037 DECAL, DangerDECAL, DANGER, Deflector Service Notes Limited Warranty