Poulan 96192002402, 422088 owner manual Troubleshooting

Page 19

TROUBLESHOOTING

See appropriate section in manual unless directed to an authorized service centre/department.

PROBLEM

 

CAUSE

 

CORRECTION

Does not start

1.

Fuel shut-off valve (if so

1.

Turn fuel shut-off valve to OPEN position.

 

 

equipped) in OFF position.

 

 

 

2.

Safety ignition key

2.

Insert safety ignition key.

 

 

is not inserted.

 

 

 

3.

Out of fuel.

3.

Fill fuel tank with fresh, clean gasoline.

 

4.

Throttle in STOP position

4.

Move throttle to FAST position

 

5.

Choke in OFF position.

5.

Move to FULL position.

 

6.

Primer not depressed.

6.

Prime as instructed in the Operation section of this manual.

 

7.

Engine is flooded.

7.

Wait a few minutes before restarting, DO NOT prime.

 

8.

Spark plug wire is

8.

Connect wire to spark plug.

 

 

disconnected.

 

 

 

9.

Bad spark plug.

9.

Replace spark plug.

 

10.

Stale fuel.

10.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

11.

Water in fuel.

11.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Reconnect spark plug wire.

 

2.

Throwing too much snow.

2.

Reduce speed and width of swath.

 

3.

Fuel tank cap is covered

3.

Remove ice and snow on and around fuel tank cap.

 

 

with ice or snow.

 

 

 

4.

Dirty or clogged muffler.

4.

Clean or replace muffler.

 

 

 

 

 

Engine idles or

1.

Choke is in FULL position.

1.

Move choke to OFF position.

runs roughly

2.

Blockage in fuel line.

2.

Clean fuel line.

 

3.

Stale fuel.

3.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

4.

Water in fuel.

4.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

5.

Carburetor is in need of

5.

Contact an authorized service centre/department.

 

 

adjustment or overhaul.

 

 

 

 

 

 

 

Excessive

1.

Loose parts or damaged

1.

Tighten all fasteners. Replace damaged parts. If vibration

vibration

 

augers or impeller.

 

remains, contact an authorized service centre/department.

 

 

 

 

 

Recoil starter

1.

Frozen recoil starter.

1.

See “IF RECOIL STARTER HAS FROZEN”

is hard to pull

 

 

 

in the Operation section of this manual.

 

 

 

 

 

Loss of traction

1.

Drive belt is worn.

1.

Check / replace drive belt.

drive / slowing

2.

Drive belt is off of pulley.

2.

Check / reinstall drive belt.

of drive speed

3.

Friction drive wheel is worn.

3.

Contact an authorized service centre/department.

 

 

 

 

 

Loss of snow

1.

Auger belt is off of pulley.

1.

Check / reinstall auger belt.

discharge or

2.

Auger belt is worn.

2.

Check / replace auger belt.

slowing of

3.

Clogged discharge chute.

3.

Clean snow chute.

snow discharge

4.

Augers / impeller jammed.

4.

Remove debris or foreign object from augers / impeller.

 

 

 

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Auger Bearing Auger HousingScraper BAR CARRIAGEBOLT5/16−18X.625Auger Assembly 30 RH Auger Assembly 30 LHDeflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentPulley Pivot LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketPivot Support Loop Handle LHLoop Handle RH Lower TubeHandle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPFlood Headlight Wire HarnessConsole Panel Headlight BezelRepair Parts Snow Thrower - Model Number XT1053ES Drive Washer Speed Selector Assembly43 402689 Drive Plate Assembly END Plate01.03.002-A Model LH358SA-159628A KEY Part Description ENGINE, TEC423184X505 Engine Mount Plate Traction Belt Belt CoverImpeller Belt Cable Bracket RH Cable Bracket LHClutch Slide CoverWheel Driver Retainer Ring Wheel Lobe35062 Safety Ignition KEYDECAL, Danger 181037DECAL, DANGER, Deflector Service Notes Limited Warranty

422088, 96192002402 specifications

The Poulan 96192002402,422088 is a powerful and versatile outdoor power equipment tool designed for a variety of gardening and landscaping tasks. Known for its reliability and performance, this equipment is ideal for both residential and commercial use. One of the standout features of the Poulan 96192002402 is its robust engine. Equipped with a high-performance 25cc gas engine, it delivers ample power for cutting through thick grass and weeds quickly and efficiently. This kind of power is crucial for maintaining a pristine yard or garden, especially during peak growing seasons when vegetation can become unruly.

The design of the Poulan 96192002402 focuses on user comfort and ease of operation. It features an ergonomic handle that reduces fatigue during extended use, allowing users to tackle larger jobs without discomfort. The lightweight construction also adds to its maneuverability, making it easy to handle in tight spaces or difficult terrain. Another significant characteristic of the Poulan 96192002402 is its innovative starting system. It incorporates a reliable start mechanism, enabling users to start the engine with minimal effort. This technology not only enhances the user experience but also ensures that the tool is ready to go whenever needed, reducing downtime.

Furthermore, this model is equipped with a dual-line bump feed system, allowing for quick and effortless line advancement. This feature is particularly beneficial for tackling stubborn weeds and other vegetation, as it ensures the cutting line maintains optimal length for efficient cutting. The Poulan 96192002402 also emphasizes durability, with a robust construction designed to withstand the rigors of outdoor use. Its quality materials ensure longevity, making it a worthwhile investment for anyone looking to maintain their outdoor spaces.

In summary, the Poulan 96192002402,422088 is an excellent choice for anyone in need of a dependable and efficient tool for gardening and landscaping tasks. With its powerful engine, user-friendly design, advanced starting system, and durable construction, this equipment is a must-have for anyone serious about maintaining their lawn and garden. Whether you are a professional landscaper or a homeowner, this tool offers the perfect balance of power and ease of use.
Top Page Image Contents