Poulan 422088 owner manual Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or ad- justments:

1.Be sure throttle is in STOP position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 21)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shoulder/shear bolt and hex nut. Should a for- eign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shoulder/shear bolt and spacer. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Connect spark plug wire to spark plug. Replace safety ignition key

IMPELLER SHEAR BOLTS

 

The impeller is secured to the impeller shaft with two (2)

 

capscrew/shear bolts and hex nuts. Should a foreign object

 

or ice become lodged in the impeller, the capscrews are

 

designed to break, preventing damage to any other com-

 

ponents. If impeller does not turn when auger control lever

 

is engaged, check to see if the capscrews have sheared.

 

To replace the capscrew/shear bolts:

16

4. Connect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

SPACER

 

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 21

TO REMOVE BELT COVER (See Fig. 22)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

3.Replace belt cover by installing cover and screws and tighten securely.

BELT

COVER

FRAME

SCREWS

FIG. 22

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Unfold Upper HandleInstall Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Deflector remote control lever used to changeHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Adjust Skid Plates See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Exploded KEY Part Description Auger Housing Scraper BARCARRIAGEBOLT5/16−18X.625 Auger BearingAuger Assembly 30 LH Auger Assembly 30 RHDeflector Control Assembly Chute WeldmentDeflector Weldment Deflector SealLEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley PivotLoop Handle LH Loop Handle RHLower Tube Pivot SupportSpacer RetainerKnob RED Handle KnobImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomWire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number XT1053ES Drive Speed Selector Assembly 43 402689 Drive Plate AssemblyEND Plate Washer01.03.002-A Model LH358SA-159628A KEY Part Description ENGINE, TEC423184X505 Engine Mount Plate Traction Belt Belt CoverImpeller Belt Cable Bracket LH Cable Bracket RHCover Wheel Driver Retainer RingWheel Lobe Clutch SlideSafety Ignition KEY 35062DECAL, Danger 181037DECAL, DANGER, Deflector Service Notes Limited Warranty

422088, 96192002402 specifications

The Poulan 96192002402,422088 is a powerful and versatile outdoor power equipment tool designed for a variety of gardening and landscaping tasks. Known for its reliability and performance, this equipment is ideal for both residential and commercial use. One of the standout features of the Poulan 96192002402 is its robust engine. Equipped with a high-performance 25cc gas engine, it delivers ample power for cutting through thick grass and weeds quickly and efficiently. This kind of power is crucial for maintaining a pristine yard or garden, especially during peak growing seasons when vegetation can become unruly.

The design of the Poulan 96192002402 focuses on user comfort and ease of operation. It features an ergonomic handle that reduces fatigue during extended use, allowing users to tackle larger jobs without discomfort. The lightweight construction also adds to its maneuverability, making it easy to handle in tight spaces or difficult terrain. Another significant characteristic of the Poulan 96192002402 is its innovative starting system. It incorporates a reliable start mechanism, enabling users to start the engine with minimal effort. This technology not only enhances the user experience but also ensures that the tool is ready to go whenever needed, reducing downtime.

Furthermore, this model is equipped with a dual-line bump feed system, allowing for quick and effortless line advancement. This feature is particularly beneficial for tackling stubborn weeds and other vegetation, as it ensures the cutting line maintains optimal length for efficient cutting. The Poulan 96192002402 also emphasizes durability, with a robust construction designed to withstand the rigors of outdoor use. Its quality materials ensure longevity, making it a worthwhile investment for anyone looking to maintain their outdoor spaces.

In summary, the Poulan 96192002402,422088 is an excellent choice for anyone in need of a dependable and efficient tool for gardening and landscaping tasks. With its powerful engine, user-friendly design, advanced starting system, and durable construction, this equipment is a must-have for anyone serious about maintaining their lawn and garden. Whether you are a professional landscaper or a homeowner, this tool offers the perfect balance of power and ease of use.
Top Page Image Contents