Poulan 96192002402, 422088 owner manual Table of Contents

Page 3

6.When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine.

7.Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous.

8.Exercise extreme caution when operating on slopes.

9.Never operate the snow thrower without proper guards, and other safety protective devices in place and work- ing.

10.Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.

11.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

12.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse.

13.Disengage power to the collector/impeller when snow thrower is transported or not in use.

14.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).

15.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

16.Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the dis- charge chute. To clear the chute:

1.SHUT THE ENGINE OFF!

2.Wait 10 seconds to be sure the impeller blades have stopped rotating.

3.Always use a clean-out tool, not your hands.

Maintenance and Storage

1.Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

2.Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and manufac- tured to give best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity

4.0 Quarts

and Type:

Unleaded Regular only

 

 

Oil Type

SAE 30 (above 40°F)

(API SG–SL):

SAE 5W-30 or 10W-30 (0° to +40°F)

 

SAE 0W-30 (below 0°F)

 

 

Oil Capacity:

26 Ounces

 

 

Spark Plug:

Champion RJ19LM (Gap: .030")

 

 

CUSTOMER RESPONSIBILITIES

•Read and observe the safety rules.

•Follow a regular schedule in maintaining, caring for and using your snow thrower.

•Follow the instructions under “Maintenance” and “Stor- age” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES

2-3

 

MAINTENANCE

14-15

PRODUCT SPECIFICATIONS

3

 

SERVICE AND ADJUSTMENTS

16-18

CUSTOMER RESPONSIBILITIES

3

 

STORAGE

18

ASSEMBLY / PRE-OPERATION

4-7

 

TROUBLESHOOTING

19

OPERATION

8-13

 

REPAIR PARTS

20-38

MAINTENANCE SCHEDULE

14

3

WARRANTY

BACK COVER

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Auger Bearing Auger HousingScraper BAR CARRIAGEBOLT5/16−18X.625Auger Assembly 30 RH Auger Assembly 30 LHDeflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentPulley Pivot LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketPivot Support Loop Handle LHLoop Handle RH Lower TubeHandle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPFlood Headlight Wire HarnessConsole Panel Headlight BezelRepair Parts Snow Thrower - Model Number XT1053ES Drive Washer Speed Selector Assembly43 402689 Drive Plate Assembly END Plate01.03.002-A KEY Part Description ENGINE, TEC Model LH358SA-159628A423184X505 Engine Mount Plate Belt Cover Traction BeltImpeller Belt Cable Bracket RH Cable Bracket LHClutch Slide CoverWheel Driver Retainer Ring Wheel Lobe35062 Safety Ignition KEY181037 DECAL, DangerDECAL, DANGER, Deflector Service Notes Limited Warranty

422088, 96192002402 specifications

The Poulan 96192002402,422088 is a powerful and versatile outdoor power equipment tool designed for a variety of gardening and landscaping tasks. Known for its reliability and performance, this equipment is ideal for both residential and commercial use. One of the standout features of the Poulan 96192002402 is its robust engine. Equipped with a high-performance 25cc gas engine, it delivers ample power for cutting through thick grass and weeds quickly and efficiently. This kind of power is crucial for maintaining a pristine yard or garden, especially during peak growing seasons when vegetation can become unruly.

The design of the Poulan 96192002402 focuses on user comfort and ease of operation. It features an ergonomic handle that reduces fatigue during extended use, allowing users to tackle larger jobs without discomfort. The lightweight construction also adds to its maneuverability, making it easy to handle in tight spaces or difficult terrain. Another significant characteristic of the Poulan 96192002402 is its innovative starting system. It incorporates a reliable start mechanism, enabling users to start the engine with minimal effort. This technology not only enhances the user experience but also ensures that the tool is ready to go whenever needed, reducing downtime.

Furthermore, this model is equipped with a dual-line bump feed system, allowing for quick and effortless line advancement. This feature is particularly beneficial for tackling stubborn weeds and other vegetation, as it ensures the cutting line maintains optimal length for efficient cutting. The Poulan 96192002402 also emphasizes durability, with a robust construction designed to withstand the rigors of outdoor use. Its quality materials ensure longevity, making it a worthwhile investment for anyone looking to maintain their outdoor spaces.

In summary, the Poulan 96192002402,422088 is an excellent choice for anyone in need of a dependable and efficient tool for gardening and landscaping tasks. With its powerful engine, user-friendly design, advanced starting system, and durable construction, this equipment is a must-have for anyone serious about maintaining their lawn and garden. Whether you are a professional landscaper or a homeowner, this tool offers the perfect balance of power and ease of use.
Top Page Image Contents