Poulan PP12TEPH30, 416751, 96198000901, PP13TEPH30 owner manual Engine, Cleaning

Page 15

MAINTENANCE

V-BELTS

Check V-belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual).

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F/0°C. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerDischarge chute control lever used to change Meets A.N.S.I. Safety RequirementsDeflector remote control lever used to change Drive speed control lever used to select forward orStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigTo USE Drift Cutters See Fig Before Starting the EngineCheck Engine OIL Level See Fig Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting 3056 2220 413609X479 413608X479Page 414280 Knob, Lever, Black Repair Parts Snow Thrower Model PP13TEPH30 Handles Repair Parts Snow Thrower Model PP13TEPH30 Handles Repair Parts Snow Thrower Model PP13TEPH30 Drive Repair Parts Snow Thrower Model PP13TEPH30 Drive Page 403842 40502996198000901 416751 416752 181037 Decal, DangerLimited Warranty

PP12TEPH30, PP13TEPH30, 96198000901, 416751 specifications

The Poulan series, including models like the 416751, PP12TEPH30, 96198000901, and PP13TEPH30, exhibits a blend of power, durability, and versatility tailored for both novice users and seasoned professionals in the outdoor power equipment arena. These models are engineered with a focus on delivering efficient performance for various lawn care and maintenance tasks.

One of the standout features of the Poulan chainsaws is their robust engine technology. The advanced two-stroke engine provides optimal power output while ensuring fuel efficiency. This means users can rely on sustained performance during intensive tasks without frequent refueling interruptions. The lightweight design of these chainsaws adds to their appeal, making them easy to handle and maneuver, reducing user fatigue during prolonged use.

In addition, the Poulan 416751 and similar models boast an automatic chain lubrication system, which ensures that the chain remains well-oiled for smoother operation and enhanced longevity. This feature not only minimizes the wear and tear on the chain but also boosts the overall safety and effectiveness of cutting operations.

The quick-release air filter on these models simplifies maintenance, allowing users to easily access the filter for cleaning and replacement, thereby promoting longer engine life. Furthermore, Poulan emphasizes user comfort with ergonomically designed handles that reduce vibrations, enabling more precise control while reducing physical strain.

Safety is paramount with the inclusion of safety features such as a chain brake, which automatically halts the chain in the event of kickback, protecting the user from potential injuries. Multiple safety mechanisms ensure that these chainsaws can be operated confidently, even by those who may be new to power equipment.

With their impressive combination of technology and design, the Poulan models like PP12TEPH30, 96198000901, and PP13TEPH30 stand out in the market. They are well-suited for a variety of tasks, from trimming branches to felling trees, making them versatile tools for landscaping and forestry work.

In summary, the Poulan chainsaws encapsulate reliability, cutting-edge technology, and user-friendly features, making them an exceptional choice for anyone looking to tackle outdoor projects with ease and efficiency. Their emphasis on power, safety, and ease of maintenance makes these models ideal companions for users seeking performance and convenience.
Top Page Image Contents