Poulan PP13TEPH30, 416751, 96198000901, PP12TEPH30 owner manual Storage, Other

Page 18

TO REMOVE WHEELS (See Fig. 26)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 26

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 2,134 meters. If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service centre/department.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service centre/ department, which has the proper equipment and experi- ence to make any necessary adjustments.

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour approximately one ounce (30 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/

18 exhaust area is still warm.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYDrive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsDeflector remote control lever used to change Discharge chute control lever used to changeHOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigScraper BAR See Fig Before Starting the EngineCheck Engine OIL Level See Fig To USE Drift Cutters See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting 3056 2220 413608X479 413609X479Page 414280 Knob, Lever, Black Repair Parts Snow Thrower Model PP13TEPH30 Handles Repair Parts Snow Thrower Model PP13TEPH30 Handles Repair Parts Snow Thrower Model PP13TEPH30 Drive Repair Parts Snow Thrower Model PP13TEPH30 Drive Page 405029 40384296198000901 181037 Decal, Danger 416751 416752Limited Warranty

PP12TEPH30, PP13TEPH30, 96198000901, 416751 specifications

The Poulan series, including models like the 416751, PP12TEPH30, 96198000901, and PP13TEPH30, exhibits a blend of power, durability, and versatility tailored for both novice users and seasoned professionals in the outdoor power equipment arena. These models are engineered with a focus on delivering efficient performance for various lawn care and maintenance tasks.

One of the standout features of the Poulan chainsaws is their robust engine technology. The advanced two-stroke engine provides optimal power output while ensuring fuel efficiency. This means users can rely on sustained performance during intensive tasks without frequent refueling interruptions. The lightweight design of these chainsaws adds to their appeal, making them easy to handle and maneuver, reducing user fatigue during prolonged use.

In addition, the Poulan 416751 and similar models boast an automatic chain lubrication system, which ensures that the chain remains well-oiled for smoother operation and enhanced longevity. This feature not only minimizes the wear and tear on the chain but also boosts the overall safety and effectiveness of cutting operations.

The quick-release air filter on these models simplifies maintenance, allowing users to easily access the filter for cleaning and replacement, thereby promoting longer engine life. Furthermore, Poulan emphasizes user comfort with ergonomically designed handles that reduce vibrations, enabling more precise control while reducing physical strain.

Safety is paramount with the inclusion of safety features such as a chain brake, which automatically halts the chain in the event of kickback, protecting the user from potential injuries. Multiple safety mechanisms ensure that these chainsaws can be operated confidently, even by those who may be new to power equipment.

With their impressive combination of technology and design, the Poulan models like PP12TEPH30, 96198000901, and PP13TEPH30 stand out in the market. They are well-suited for a variety of tasks, from trimming branches to felling trees, making them versatile tools for landscaping and forestry work.

In summary, the Poulan chainsaws encapsulate reliability, cutting-edge technology, and user-friendly features, making them an exceptional choice for anyone looking to tackle outdoor projects with ease and efficiency. Their emphasis on power, safety, and ease of maintenance makes these models ideal companions for users seeking performance and convenience.
Top Page Image Contents