Poulan XT824ES Before Starting the Engine, To Adjust Skid Plates See Fig, Scraper BAR See Fig

Page 11

OPERATION

TO ADJUST SKID PLATES (See Fig. 16)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the hex nuts, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION

 

(LOW GROUND

 

CLEARANCE)

 

 

AUGER

 

HOUSING

 

SCRAPER BAR

HEX

SKID PLATE

NUTS

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 16

SCRAPER BAR (See Fig. 16)

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 17)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 17)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gaso- hol or using ethanol or methanol) can attract moisture which leads to separation and forma- tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

CHOKE

ENGINE OIL

GASOLINE

CONTROL

FILL CAP / DIPSTICK

FILLER CAP

STARTER

BUTTON

PRIMER

RECOIL

 

SAFETY

STARTER

HANDLE

IGNITION

ON / OFF

KEY

SWITCH

 

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 17

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Figs HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Exploded KEY Part Description Bearing Plug Auger HousingScraper BAR Auger BearingSkid Plate RH Auger Assembly LHAuger Assembly RH Skid Plate LHRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldStrap Chute WeldmentDeflector Weldment Deflector SealRepair Parts Snow Thrower - Model NO. XT824ES Handles Interlock CAM Lower TubePivot Support Interlock SpringWasher 3/8 SpacerKnob RED Handle KnobShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPRepair Parts Snow Thrower - Model NO. XT824ES Drive Rubber Ring AssemblyDrive Plate Assembly Speed SelectorClik PIN Axle ShaftRoll PIN 3/16 Sprocket423185X505 Cover AssemblyEngine Model 12A114 FrameIdler Pulley Impeller BeltTraction Belt Idler ARM BracketWheel Assembly LH Repair Parts Snow Thrower - Model NO. XT824ES Wheels193071 Repair Parts Snow Thrower - Model NO. XT824ES BAG of PartsSafety Ignition KEY DECAL, Danger Repair Parts Snow Thrower - Model NO. XT824ESDecals 181037Service Notes Service Notes Limited Warranty

XT824ES, 96192003300 specifications

The Poulan 96192003300, XT824ES is a standout model in the realm of snow blowers, designed to tackle even the harshest winter conditions with ease. Engineered for both residential and light commercial use, it combines performance, durability, and user-friendly features, making it a reliable choice for snow removal.

One of the main features of the XT824ES is its powerful 24-inch clearing width, allowing users to efficiently clear driveways, sidewalks, and patios in fewer passes. The robust 208cc engine delivers ample power, ensuring that the machine can handle heavy and wet snow without straining. This impressive clearing capacity enables users to complete their snow removal tasks quickly and effectively.

The snow thrower also boasts an easy electric start system, ensuring that you can fire it up with minimal effort, even in extreme winter temperatures. This eliminates the hassle of manual starting, enhancing user convenience, especially on those cold mornings when quick action is essential.

The XT824ES utilizes a two-stage snow removal process, which is particularly effective for dealing with packed snow and ice. The first stage involves the auger that collects the snow, while the impeller then propels it out through the chute, allowing for a significant distance of snow discharge. Users can adjust the chute direction with a simple tilt, adding to the overall versatility of the machine.

Another notable characteristic of this snow blower is its rugged construction. Made with durable materials, the XT824ES is built to withstand the rigors of winter operation. The heavy-duty steel frame and auger system ensure longevity and reliability, providing confidence to users that it will perform season after season.

For user comfort, the XT824ES features adjustable handles, allowing for a more ergonomic grip, which can reduce strain during prolonged use. The machine is also equipped with large, rugged wheels designed for enhanced traction and maneuverability, making it easier to navigate through deep snow and across uneven terrain.

In summary, the Poulan 96192003300, XT824ES snow blower is a powerful and efficient tool for anyone looking to tackle snow removal tasks effectively. With its combination of robust features, user-friendly technologies, and durable design, it stands out as a valuable asset for winter maintenance. Whether you’re dealing with light flurries or heavy snowfalls, the XT824ES is equipped to get the job done reliably and efficiently.
Top Page Image Contents