Poulan XT824ES, 96192003300 HOW to USE Your Snow Thrower, Stopping, To USE Choke Control See Fig

Page 9

OPERATION

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear

safety glasses or eye shields while operating 00155 your snow thrower or performing any adjust- ments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

•Release the auger control lever to stop throwing snow.

ENGINE

1.Move ON / OFF switch to “OFF” position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE CHOKE CONTROL (See Fig. 11)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

•To engage choke, turn knob counterclockwise. Slowly turn knob clockwise to disengage.

OFF

 

 

FULL

 

 

 

 

 

FIG. 11

TO CONTROL SNOW DISCHARGE (See Figs. 12 & 13)

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

WARNING: If the discharge chute or auger become clogged, shut-off engine and wait for all moving parts to stop. Use the clean-out tool, NOT YOUR HANDS, to unclog the chute and/or auger.

The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever.

•To change the discharge chute position, press downward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROL LEVER

FIG. 12

The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther.

•To change the deflector position, loosen knob, move de- flector to desired position and tighten knob securely.

HIGH

POSITION

KNOB

CHUTE

DEFLECTOR

LOW POSITION

FIG. 13

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Choke Control See Fig To Control Snow Discharge See FigsUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting Exploded KEY Part Description Scraper BAR Auger HousingAuger Bearing Bearing PlugAuger Assembly RH Auger Assembly LHSkid Plate LH Skid Plate RHCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadDeflector Weldment Chute WeldmentDeflector Seal StrapRepair Parts Snow Thrower - Model NO. XT824ES Handles Pivot Support Lower TubeInterlock Spring Interlock CAMKnob RED SpacerHandle Knob Washer 3/8Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomRepair Parts Snow Thrower - Model NO. XT824ES Drive Drive Plate Assembly AssemblySpeed Selector Rubber RingRoll PIN 3/16 Axle ShaftSprocket Clik PINEngine Model 12A114 Cover AssemblyFrame 423185X505Traction Belt Impeller BeltIdler ARM Bracket Idler PulleyWheel Assembly LH Repair Parts Snow Thrower - Model NO. XT824ES WheelsRepair Parts Snow Thrower - Model NO. XT824ES BAG of Parts Safety Ignition KEY193071 Decals Repair Parts Snow Thrower - Model NO. XT824ES181037 DECAL, DangerService Notes Service Notes Limited Warranty

XT824ES, 96192003300 specifications

The Poulan 96192003300, XT824ES is a standout model in the realm of snow blowers, designed to tackle even the harshest winter conditions with ease. Engineered for both residential and light commercial use, it combines performance, durability, and user-friendly features, making it a reliable choice for snow removal.

One of the main features of the XT824ES is its powerful 24-inch clearing width, allowing users to efficiently clear driveways, sidewalks, and patios in fewer passes. The robust 208cc engine delivers ample power, ensuring that the machine can handle heavy and wet snow without straining. This impressive clearing capacity enables users to complete their snow removal tasks quickly and effectively.

The snow thrower also boasts an easy electric start system, ensuring that you can fire it up with minimal effort, even in extreme winter temperatures. This eliminates the hassle of manual starting, enhancing user convenience, especially on those cold mornings when quick action is essential.

The XT824ES utilizes a two-stage snow removal process, which is particularly effective for dealing with packed snow and ice. The first stage involves the auger that collects the snow, while the impeller then propels it out through the chute, allowing for a significant distance of snow discharge. Users can adjust the chute direction with a simple tilt, adding to the overall versatility of the machine.

Another notable characteristic of this snow blower is its rugged construction. Made with durable materials, the XT824ES is built to withstand the rigors of winter operation. The heavy-duty steel frame and auger system ensure longevity and reliability, providing confidence to users that it will perform season after season.

For user comfort, the XT824ES features adjustable handles, allowing for a more ergonomic grip, which can reduce strain during prolonged use. The machine is also equipped with large, rugged wheels designed for enhanced traction and maneuverability, making it easier to navigate through deep snow and across uneven terrain.

In summary, the Poulan 96192003300, XT824ES snow blower is a powerful and efficient tool for anyone looking to tackle snow removal tasks effectively. With its combination of robust features, user-friendly technologies, and durable design, it stands out as a valuable asset for winter maintenance. Whether you’re dealing with light flurries or heavy snowfalls, the XT824ES is equipped to get the job done reliably and efficiently.
Top Page Image Contents