Poulan 96192003300, XT824ES owner manual Storage, Other, Fuel System, Engine OIL, Cylinder

Page 18

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigsUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Exploded KEY Part Description Auger Bearing Auger HousingScraper BAR Bearing PlugSkid Plate LH Auger Assembly LHAuger Assembly RH Skid Plate RHCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadDeflector Seal Chute WeldmentDeflector Weldment StrapRepair Parts Snow Thrower - Model NO. XT824ES Handles Interlock Spring Lower TubePivot Support Interlock CAMHandle Knob SpacerKnob RED Washer 3/8Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomRepair Parts Snow Thrower - Model NO. XT824ES Drive Speed Selector AssemblyDrive Plate Assembly Rubber RingSprocket Axle ShaftRoll PIN 3/16 Clik PINFrame Cover AssemblyEngine Model 12A114 423185X505Idler ARM Bracket Impeller BeltTraction Belt Idler PulleyRepair Parts Snow Thrower - Model NO. XT824ES Wheels Wheel Assembly LHRepair Parts Snow Thrower - Model NO. XT824ES BAG of Parts Safety Ignition KEY193071 181037 Repair Parts Snow Thrower - Model NO. XT824ESDecals DECAL, DangerService Notes Service Notes Limited Warranty

XT824ES, 96192003300 specifications

The Poulan 96192003300, XT824ES is a standout model in the realm of snow blowers, designed to tackle even the harshest winter conditions with ease. Engineered for both residential and light commercial use, it combines performance, durability, and user-friendly features, making it a reliable choice for snow removal.

One of the main features of the XT824ES is its powerful 24-inch clearing width, allowing users to efficiently clear driveways, sidewalks, and patios in fewer passes. The robust 208cc engine delivers ample power, ensuring that the machine can handle heavy and wet snow without straining. This impressive clearing capacity enables users to complete their snow removal tasks quickly and effectively.

The snow thrower also boasts an easy electric start system, ensuring that you can fire it up with minimal effort, even in extreme winter temperatures. This eliminates the hassle of manual starting, enhancing user convenience, especially on those cold mornings when quick action is essential.

The XT824ES utilizes a two-stage snow removal process, which is particularly effective for dealing with packed snow and ice. The first stage involves the auger that collects the snow, while the impeller then propels it out through the chute, allowing for a significant distance of snow discharge. Users can adjust the chute direction with a simple tilt, adding to the overall versatility of the machine.

Another notable characteristic of this snow blower is its rugged construction. Made with durable materials, the XT824ES is built to withstand the rigors of winter operation. The heavy-duty steel frame and auger system ensure longevity and reliability, providing confidence to users that it will perform season after season.

For user comfort, the XT824ES features adjustable handles, allowing for a more ergonomic grip, which can reduce strain during prolonged use. The machine is also equipped with large, rugged wheels designed for enhanced traction and maneuverability, making it easier to navigate through deep snow and across uneven terrain.

In summary, the Poulan 96192003300, XT824ES snow blower is a powerful and efficient tool for anyone looking to tackle snow removal tasks effectively. With its combination of robust features, user-friendly technologies, and durable design, it stands out as a valuable asset for winter maintenance. Whether you’re dealing with light flurries or heavy snowfalls, the XT824ES is equipped to get the job done reliably and efficiently.
Top Page Image Contents