Poulan XT824ES Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 15

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 18)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a spacer, shear bolt and hex nut. Should a foreign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever is engaged, check to see if the capscrews have sheared. To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 18

TO REMOVE BELT COVER (See Fig. 19)

1.Remove the two screws securing belt cover to frame.

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten securely.

FRAME

BELT COVER

SCREWS

15

FIG. 19

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Figs HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Exploded KEY Part Description Bearing Plug Auger HousingScraper BAR Auger BearingSkid Plate RH Auger Assembly LHAuger Assembly RH Skid Plate LHRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldStrap Chute WeldmentDeflector Weldment Deflector SealRepair Parts Snow Thrower - Model NO. XT824ES Handles Interlock CAM Lower TubePivot Support Interlock SpringWasher 3/8 SpacerKnob RED Handle KnobShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPRepair Parts Snow Thrower - Model NO. XT824ES Drive Rubber Ring AssemblyDrive Plate Assembly Speed SelectorClik PIN Axle ShaftRoll PIN 3/16 Sprocket423185X505 Cover AssemblyEngine Model 12A114 FrameIdler Pulley Impeller BeltTraction Belt Idler ARM BracketWheel Assembly LH Repair Parts Snow Thrower - Model NO. XT824ES WheelsRepair Parts Snow Thrower - Model NO. XT824ES BAG of Parts Safety Ignition KEY193071 DECAL, Danger Repair Parts Snow Thrower - Model NO. XT824ESDecals 181037Service Notes Service Notes Limited Warranty

XT824ES, 96192003300 specifications

The Poulan 96192003300, XT824ES is a standout model in the realm of snow blowers, designed to tackle even the harshest winter conditions with ease. Engineered for both residential and light commercial use, it combines performance, durability, and user-friendly features, making it a reliable choice for snow removal.

One of the main features of the XT824ES is its powerful 24-inch clearing width, allowing users to efficiently clear driveways, sidewalks, and patios in fewer passes. The robust 208cc engine delivers ample power, ensuring that the machine can handle heavy and wet snow without straining. This impressive clearing capacity enables users to complete their snow removal tasks quickly and effectively.

The snow thrower also boasts an easy electric start system, ensuring that you can fire it up with minimal effort, even in extreme winter temperatures. This eliminates the hassle of manual starting, enhancing user convenience, especially on those cold mornings when quick action is essential.

The XT824ES utilizes a two-stage snow removal process, which is particularly effective for dealing with packed snow and ice. The first stage involves the auger that collects the snow, while the impeller then propels it out through the chute, allowing for a significant distance of snow discharge. Users can adjust the chute direction with a simple tilt, adding to the overall versatility of the machine.

Another notable characteristic of this snow blower is its rugged construction. Made with durable materials, the XT824ES is built to withstand the rigors of winter operation. The heavy-duty steel frame and auger system ensure longevity and reliability, providing confidence to users that it will perform season after season.

For user comfort, the XT824ES features adjustable handles, allowing for a more ergonomic grip, which can reduce strain during prolonged use. The machine is also equipped with large, rugged wheels designed for enhanced traction and maneuverability, making it easier to navigate through deep snow and across uneven terrain.

In summary, the Poulan 96192003300, XT824ES snow blower is a powerful and efficient tool for anyone looking to tackle snow removal tasks effectively. With its combination of robust features, user-friendly technologies, and durable design, it stands out as a valuable asset for winter maintenance. Whether you’re dealing with light flurries or heavy snowfalls, the XT824ES is equipped to get the job done reliably and efficiently.
Top Page Image Contents