Poulan XT824ES, 96192003300 owner manual Troubleshooting

Page 19

TROUBLESHOOTING

See appropriate section in manual unless directed to an authorized service center/department.

PROBLEM

 

CAUSE

 

CORRECTION

Does not start

1.

Fuel shut-off valve (if so

1.

Turn fuel shut-off valve to OPEN position.

 

 

equipped) in OFF position.

 

 

 

2.

Safety ignition key

2.

Insert safety ignition key.

 

 

is not inserted.

 

 

 

3.

Out of fuel.

3.

Fill fuel tank with fresh, clean gasoline.

 

4.

Throttle in STOP position

4.

Move throttle to FAST position

 

 

(or ON/OFF switch is OFF).

 

(or ON/OFF switch to ON position).

 

5.

Choke in OFF position.

5.

Move to FULL position.

 

6.

Primer not depressed.

6.

Prime as instructed in the Operation section of this manual.

 

7.

Engine is flooded.

7.

Wait a few minutes before restarting, DO NOT prime.

 

8.

Spark plug wire is

8.

Connect wire to spark plug.

 

 

disconnected.

 

 

 

9.

Bad spark plug.

9.

Replace spark plug.

 

10.

Stale fuel.

10.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

11.

Water in fuel.

11.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Reconnect spark plug wire.

 

2.

Throwing too much snow.

2.

Reduce speed and width of swath.

 

3.

Fuel tank cap is covered

3.

Remove ice and snow on and around fuel tank cap.

 

 

with ice or snow.

 

 

 

4.

Dirty or clogged muffler.

4.

Clean or replace muffler.

 

 

 

 

 

Engine idles or

1.

Choke is in FULL position.

1.

Move choke to OFF position.

runs roughly

2.

Blockage in fuel line.

2.

Clean fuel line.

 

3.

Stale fuel.

3.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

4.

Water in fuel.

4.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

5.

Carburetor is in need of

5.

Contact an authorized service center/department.

 

 

adjustment or overhaul.

 

 

 

 

 

 

 

Excessive

1.

Loose parts or damaged

1.

Tighten all fasteners. Replace damaged parts. If vibration

vibration

 

augers or impeller.

 

remains, contact an authorized service center/department.

 

 

 

 

 

Recoil starter

1.

Frozen recoil starter.

1.

See “IF RECOIL STARTER HAS FROZEN”

is hard to pull

 

 

 

in the Operation section of this manual.

 

 

 

 

 

Loss of traction

1.

Drive belt is worn.

1.

Check / replace drive belt.

drive / slowing

2.

Drive belt is off of pulley.

2.

Check / reinstall drive belt.

of drive speed

3.

Friction drive wheel is worn.

3.

Contact an authorized service center/department.

 

 

 

 

 

Loss of snow

1.

Auger belt is off of pulley.

1.

Check / reinstall auger belt.

discharge or

2.

Auger belt is worn.

2.

Check / replace auger belt.

slowing of

3.

Clogged discharge chute.

3.

Clean snow chute.

snow discharge

4.

Augers / impeller jammed.

4.

Remove debris or foreign object from augers / impeller.

 

 

 

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Figs HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Exploded KEY Part Description Bearing Plug Auger HousingScraper BAR Auger BearingSkid Plate RH Auger Assembly LHAuger Assembly RH Skid Plate LHRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldStrap Chute WeldmentDeflector Weldment Deflector SealRepair Parts Snow Thrower - Model NO. XT824ES Handles Interlock CAM Lower TubePivot Support Interlock SpringWasher 3/8 SpacerKnob RED Handle KnobShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPRepair Parts Snow Thrower - Model NO. XT824ES Drive Rubber Ring AssemblyDrive Plate Assembly Speed SelectorClik PIN Axle ShaftRoll PIN 3/16 Sprocket423185X505 Cover AssemblyEngine Model 12A114 FrameIdler Pulley Impeller BeltTraction Belt Idler ARM BracketWheel Assembly LH Repair Parts Snow Thrower - Model NO. XT824ES WheelsSafety Ignition KEY Repair Parts Snow Thrower - Model NO. XT824ES BAG of Parts193071 DECAL, Danger Repair Parts Snow Thrower - Model NO. XT824ESDecals 181037Service Notes Service Notes Limited Warranty

XT824ES, 96192003300 specifications

The Poulan 96192003300, XT824ES is a standout model in the realm of snow blowers, designed to tackle even the harshest winter conditions with ease. Engineered for both residential and light commercial use, it combines performance, durability, and user-friendly features, making it a reliable choice for snow removal.

One of the main features of the XT824ES is its powerful 24-inch clearing width, allowing users to efficiently clear driveways, sidewalks, and patios in fewer passes. The robust 208cc engine delivers ample power, ensuring that the machine can handle heavy and wet snow without straining. This impressive clearing capacity enables users to complete their snow removal tasks quickly and effectively.

The snow thrower also boasts an easy electric start system, ensuring that you can fire it up with minimal effort, even in extreme winter temperatures. This eliminates the hassle of manual starting, enhancing user convenience, especially on those cold mornings when quick action is essential.

The XT824ES utilizes a two-stage snow removal process, which is particularly effective for dealing with packed snow and ice. The first stage involves the auger that collects the snow, while the impeller then propels it out through the chute, allowing for a significant distance of snow discharge. Users can adjust the chute direction with a simple tilt, adding to the overall versatility of the machine.

Another notable characteristic of this snow blower is its rugged construction. Made with durable materials, the XT824ES is built to withstand the rigors of winter operation. The heavy-duty steel frame and auger system ensure longevity and reliability, providing confidence to users that it will perform season after season.

For user comfort, the XT824ES features adjustable handles, allowing for a more ergonomic grip, which can reduce strain during prolonged use. The machine is also equipped with large, rugged wheels designed for enhanced traction and maneuverability, making it easier to navigate through deep snow and across uneven terrain.

In summary, the Poulan 96192003300, XT824ES snow blower is a powerful and efficient tool for anyone looking to tackle snow removal tasks effectively. With its combination of robust features, user-friendly technologies, and durable design, it stands out as a valuable asset for winter maintenance. Whether you’re dealing with light flurries or heavy snowfalls, the XT824ES is equipped to get the job done reliably and efficiently.
Top Page Image Contents