Poulan 96194000503 HOW to SET UP Your Snow Thrower, Tool BOX See Fig, Unfold Upper Handle

Page 5

ASSEMBLY / PRE-OPERATION

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 8)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD
	RETAINER
	SPRING
SPEED	SPEED
CONTROL	CONTROL
BRACKET	LEVER

FIG. 2

5

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP

OPENING

DOWN

PIVOT

BRACKET

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

Image 5

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONParts Packed Separately in Carton Install Speed Control ROD See Figs HOW to SET UP Your Snow ThrowerInstall Traction Drive Control ROD See Figs Tool BOX See FigCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo USE Choke Control See Fig To Control Snow Discharge See FigsTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage Other TroubleshootingFuncionamiento ¡ATENCIÓN! ¡ESTE ALERTO! SU Seguridad Esta ComprometidaPreparación Montaje / PRE-OPERACIÓN Tabla DE MateriasSacar LA Máquina Quitanieves DEL Cartón Montaje / PRE-OPERACIÓNDesplegar LA Empuñadura Superior Como Preparar SU Máquina QuitanievesMontar LA Biela Montaje DE LA BielaControlar LA Presión DE LOS Neumáticos DE Mando DE LA Barrena Ver Figs yFamiliarícese CON SU Máquina Quitanieves OperaciónCumple CON LOS Requisitos DE Seguridad DE LA A.N.S.I Como Utilizar SU Máquina Quitanieves Controlar LA Eyección DE LA NievePararse Usar EL Control DE LA Estrangulación Ver FigMoverse Adelante Y Atrás Ver Fig Lanzar LA Nieve Ver FigUsar LA Herramienta Para Limpiar Ver Fig Puesta EN Marcha DEL Motor Antes DE Poner EN Marcha EL MotorPuesta EN Marcha CON EL Motor Frío Arrancador Eléctrico Consejos Para Lanzar LA NieveAntes DE Parar Recomendaciones Generales MantenamientoLubricación Maquina QuitanievesLimpieza MotorPara Ajustar LA Altura DE Máquina Quitanieves Servicio Y AdjustesConducto Deflector Pernos DE Seguridad Ver FigVaciar LA Gasolina DEL Depósito DE Carburante Sustituir LAS Correas Vea FigOtros AlmacenimientoIdentificacion DE Problemas Exploded KEY Part Description Scrapper BAR Auger HousingAuger 24 LH Auger 24 RHBearing Plug Auger BearingPOP Rivet Knob BlackWasher Plastic WasherRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley PivotRetainer SpacerKnob RED Handle KnobHandle Grip Panel Bracket LH Panel Bracket RHLower Handle Pivot Support WeldmentCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Part KEY Description Repair Parts Snow Thrower Model Number 96194000503 Drive END Plate 43 402689 Drive Plate AssemblyControl ARM Clevis PINRoll PIN 3/16 Axle ShaftSprocket Clik PINFrame Engine ModelEngine Mount Plate Belt Cover187866X417 Wheel Assembly LH187831X417 Safety Ignition KEY Power CordRetainer PIN WrenchDECAL, DANGER, Deflector 181038DECAL, Danger Service Notes Service Notes Service Notes Limited Warranty