Poulan 96194000503 HOW to USE Your Snow Thrower, Stopping, To USE Choke Control See Fig

Page 9

OPERATION

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear

safety glasses or eye shields while operating 00155 your snow thrower or performing any adjust- ments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

Release the auger control lever to stop throwing snow.

ENGINE

1.Move ON / OFF switch to “OFF” position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE CHOKE CONTROL (See Fig. 9)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

To engage choke, turn knob counterclockwise. Slowly turn knob clockwise to disengage.

OFF

 

FULL

 

 

 

 

FIG. 9

TO CONTROL SNOW DISCHARGE (See Figs. 10 & 11)

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

WARNING: If the discharge chute or auger become clogged, shut-off engine and wait for all moving parts to stop. Use the clean-out tool, NOT YOUR HANDS, to unclog the chute and/or auger.

The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever.

To change the discharge chute position, press downward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROL LEVER

FIG. 10

The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther.

To change the deflector position, loosen knob, move de- flector to desired position and tighten knob securely.

HIGH

POSITION

KNOB

CHUTE

DEFLECTOR

LOW POSITION

FIG. 11

9

Image 9
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION Parts Packed Separately in CartonRemove Snow Thrower from Carton Install Speed Control ROD See Figs HOW to SET UP Your Snow ThrowerInstall Traction Drive Control ROD See Figs Tool BOX See FigInstall Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo USE Choke Control See Fig To Control Snow Discharge See FigsUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage Other Troubleshooting¡ATENCIÓN! ¡ESTE ALERTO! SU Seguridad Esta Comprometida PreparaciónFuncionamiento Montaje / PRE-OPERACIÓN Tabla DE MateriasSacar LA Máquina Quitanieves DEL Cartón Montaje / PRE-OPERACIÓNDesplegar LA Empuñadura Superior Como Preparar SU Máquina QuitanievesMontar LA Biela Montaje DE LA BielaControlar LA Presión DE LOS Neumáticos DE Mando DE LA Barrena Ver Figs yFamiliarícese CON SU Máquina Quitanieves OperaciónCumple CON LOS Requisitos DE Seguridad DE LA A.N.S.I Como Utilizar SU Máquina Quitanieves Controlar LA Eyección DE LA NievePararse Usar EL Control DE LA Estrangulación Ver FigLanzar LA Nieve Ver Fig Usar LA Herramienta Para Limpiar Ver FigMoverse Adelante Y Atrás Ver Fig Puesta EN Marcha DEL Motor Antes DE Poner EN Marcha EL MotorConsejos Para Lanzar LA Nieve Antes DE PararPuesta EN Marcha CON EL Motor Frío Arrancador Eléctrico Recomendaciones Generales MantenamientoLubricación Maquina QuitanievesLimpieza MotorPara Ajustar LA Altura DE Máquina Quitanieves Servicio Y AdjustesConducto Deflector Pernos DE Seguridad Ver FigVaciar LA Gasolina DEL Depósito DE Carburante Sustituir LAS Correas Vea FigOtros AlmacenimientoIdentificacion DE Problemas Exploded KEY Part Description Scrapper BAR Auger HousingAuger 24 LH Auger 24 RHBearing Plug Auger BearingPOP Rivet Knob BlackWasher Plastic WasherRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley PivotRetainer SpacerKnob RED Handle KnobHandle Grip Panel Bracket LH Panel Bracket RHLower Handle Pivot Support WeldmentCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Part KEY Description Repair Parts Snow Thrower Model Number 96194000503 Drive END Plate 43 402689 Drive Plate AssemblyControl ARM Clevis PINRoll PIN 3/16 Axle ShaftSprocket Clik PINFrame Engine ModelEngine Mount Plate Belt CoverWheel Assembly LH 187831X417187866X417 Safety Ignition KEY Power CordRetainer PIN Wrench181038 DECAL, DangerDECAL, DANGER, Deflector Service Notes Service Notes Service Notes Limited Warranty