Poulan 96194000503 owner manual Install Auger Control ROD See Figs, Check Tire Pressure

Page 6

ASSEMBLY / PRE-OPERATION

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

2.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

RUBBER

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

FIG. 6

INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotator head over chute bracket. If neces- sary,rotatechuteassemblytoalignsquareandpinonun- derside of chute rotator head with holes in chute bracket.

3.With chute rotator head and chute bracket aligned, position chute rotator head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE
ROTATOR		3/8 LOCKNUT
HEAD
		3/8 WASHER
		PIN
		THREADED
		STUD
	ALIGN BEFORE	ROTATOR HEAD
CHUTE	ALIGN BEFORE	MOUNTING
BRACKET	TIGHTENING LOCKNUT	BRACKET

FIG. 7

CHECK TIRE PRESSURE

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI (19-24.5 N-m).

6

Image 6

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION Parts Packed Separately in CartonRemove Snow Thrower from Carton Install Traction Drive Control ROD See Figs HOW to SET UP Your Snow ThrowerInstall Speed Control ROD See Figs Tool BOX See FigInstall Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements To USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigsUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage Troubleshooting Other¡ATENCIÓN! ¡ESTE ALERTO! SU Seguridad Esta Comprometida PreparaciónFuncionamiento Tabla DE Materias Montaje / PRE-OPERACIÓNMontaje / PRE-OPERACIÓN Sacar LA Máquina Quitanieves DEL CartónMontar LA Biela Como Preparar SU Máquina QuitanievesDesplegar LA Empuñadura Superior Montaje DE LA BielaDE Mando DE LA Barrena Ver Figs y Controlar LA Presión DE LOS NeumáticosOperación Familiarícese CON SU Máquina QuitanievesCumple CON LOS Requisitos DE Seguridad DE LA A.N.S.I Pararse Controlar LA Eyección DE LA NieveComo Utilizar SU Máquina Quitanieves Usar EL Control DE LA Estrangulación Ver FigLanzar LA Nieve Ver Fig Usar LA Herramienta Para Limpiar Ver FigMoverse Adelante Y Atrás Ver Fig Antes DE Poner EN Marcha EL Motor Puesta EN Marcha DEL MotorConsejos Para Lanzar LA Nieve Antes DE PararPuesta EN Marcha CON EL Motor Frío Arrancador Eléctrico Lubricación MantenamientoRecomendaciones Generales Maquina QuitanievesMotor LimpiezaConducto Deflector Servicio Y AdjustesPara Ajustar LA Altura DE Máquina Quitanieves Pernos DE Seguridad Ver FigSustituir LAS Correas Vea Fig Vaciar LA Gasolina DEL Depósito DE CarburanteAlmacenimiento OtrosIdentificacion DE Problemas Exploded KEY Part Description Auger 24 LH Auger HousingScrapper BAR Auger 24 RHAuger Bearing Bearing PlugWasher Knob BlackPOP Rivet Plastic WasherRotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley PivotKnob RED SpacerRetainer Handle KnobLower Handle Panel Bracket LH Panel Bracket RHHandle Grip Pivot Support WeldmentCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Part KEY Description Repair Parts Snow Thrower Model Number 96194000503 Drive Control ARM 43 402689 Drive Plate AssemblyEND Plate Clevis PINSprocket Axle ShaftRoll PIN 3/16 Clik PINEngine Mount Plate Engine ModelFrame Belt CoverWheel Assembly LH 187831X417187866X417 Retainer PIN Power CordSafety Ignition KEY Wrench181038 DECAL, DangerDECAL, DANGER, Deflector Service Notes Service Notes Service Notes Limited Warranty