Poulan 96194000503 owner manual Meets A.N.S.I. Safety Requirements

Page 8

OPERATION

GASOLINE

FILLER CAP

MUFFLER

CHOKE CON-

TROL

PRIMER

ELECTRIC	AUGER	DEFLECTOR REMOTE	TRACTION DRIVE
START BUTTON	CONTROL	DEFLECTOR REMOTE	TRACTION DRIVE
	LEVER	CONTROL LEVER	CONTROL LEVER
RECOIL		DRIVE SPEED
(AUXILIARY)		CONTROL LEVER
STARTER
HANDLE
	CHUTE
DEFLECTOR
			LIGHT

SAFETY

IGNITION

KEY ON / OFF SWITCH

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

DISCHARGE

CHUTE

CLEAN-OUT

TOOL

FIG. 8

DISCHARGE CHUTE CONTROL KNOB

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke control - used for starting a cold engine.

8

Throttle/engine control - used to select either FAST or SLOW engine speed and to STOP the engine.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control knob - used to change the direction the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

Image 8

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONParts Packed Separately in Carton HOW to SET UP Your Snow Thrower Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Tool BOX See FigCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigsTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage Troubleshooting OtherFuncionamiento ¡ATENCIÓN! ¡ESTE ALERTO! SU Seguridad Esta ComprometidaPreparación Tabla DE Materias Montaje / PRE-OPERACIÓNMontaje / PRE-OPERACIÓN Sacar LA Máquina Quitanieves DEL CartónComo Preparar SU Máquina Quitanieves Desplegar LA Empuñadura SuperiorMontar LA Biela Montaje DE LA BielaDE Mando DE LA Barrena Ver Figs y Controlar LA Presión DE LOS NeumáticosOperación Familiarícese CON SU Máquina QuitanievesCumple CON LOS Requisitos DE Seguridad DE LA A.N.S.I Controlar LA Eyección DE LA Nieve Como Utilizar SU Máquina QuitanievesPararse Usar EL Control DE LA Estrangulación Ver FigMoverse Adelante Y Atrás Ver Fig Lanzar LA Nieve Ver FigUsar LA Herramienta Para Limpiar Ver Fig Antes DE Poner EN Marcha EL Motor Puesta EN Marcha DEL MotorPuesta EN Marcha CON EL Motor Frío Arrancador Eléctrico Consejos Para Lanzar LA NieveAntes DE Parar Mantenamiento Recomendaciones GeneralesLubricación Maquina QuitanievesMotor LimpiezaServicio Y Adjustes Para Ajustar LA Altura DE Máquina QuitanievesConducto Deflector Pernos DE Seguridad Ver FigSustituir LAS Correas Vea Fig Vaciar LA Gasolina DEL Depósito DE CarburanteAlmacenimiento OtrosIdentificacion DE Problemas Exploded KEY Part Description Auger Housing Scrapper BARAuger 24 LH Auger 24 RHAuger Bearing Bearing PlugKnob Black POP RivetWasher Plastic WasherLEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley PivotSpacer RetainerKnob RED Handle KnobPanel Bracket LH Panel Bracket RH Handle GripLower Handle Pivot Support WeldmentCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Part KEY Description Repair Parts Snow Thrower Model Number 96194000503 Drive 43 402689 Drive Plate Assembly END PlateControl ARM Clevis PINAxle Shaft Roll PIN 3/16Sprocket Clik PINEngine Model FrameEngine Mount Plate Belt Cover187866X417 Wheel Assembly LH187831X417 Power Cord Safety Ignition KEYRetainer PIN WrenchDECAL, DANGER, Deflector 181038DECAL, Danger Service Notes Service Notes Service Notes Limited Warranty