Poulan 961980019 owner manual Engine, Cleaning

Page 14

MAINTENANCE

V-BELTS

Check V-belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual).

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F/0°C. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug and place wire where it can- not come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYRecoil auxiliary starter handle used for starting Skid PlateTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigsTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR ADD Gasoline See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Service Notes   413607X479 413606X479155377 Page 414280 Knob, Lever, Black 1724 KEY Part Description Repair Parts Drive Repair Parts Snow Thrower Model 961980019 96198001901 Drive Page KEY Part Description   KEY Part Description Limited Warranty

961980019 specifications

The Poulan 961980019 is a dependable and robust chainsaw designed for both novice and experienced users seeking an efficient tool for various cutting tasks. Renowned for its reliability and performance, this model is ideal for homeowners, landscapers, and woodworkers alike.

One of the standout features of the Poulan 961980019 is its powerful engine. Equipped with a reliable 42cc two-cycle engine, the chainsaw delivers strong cutting performance and consistent power, making it suitable for slicing through trees, logs, and other tough materials with ease. The engine's design ensures reduced emissions, promoting a more environmentally friendly operation without compromising on power.

The chainsaw features a 16-inch bar, providing a good balance between cutting capacity and maneuverability. This length is perfect for medium-sized tasks, allowing users to make efficient cuts without the weight of larger models. Coupled with a high chain speed, the Poulan 961980019 provides quick and clean cuts, enhancing productivity and efficiency in both home and professional settings.

Another notable characteristic is the chainsaw's lightweight construction. Weighing only 10 lbs, it minimizes user fatigue, making it easy to handle during extended use. The ergonomic design, featuring a comfortable grip and well-placed controls, ensures that users can operate the saw with confidence and ease.

The Poulan 961980019 also incorporates advanced technologies for enhanced safety and convenience. Its automatic chain oiling system provides continuous lubrication, which extends the life of the chain and bar while reducing wear and tear. Additionally, it includes a chain brake feature that helps protect users from kickback accidents, enhancing safety during operation.

The chainsaw is designed for easy maintenance, featuring a tool-less chain adjustment that allows users to make quick adjustments on the go. This means less downtime and more efficient work sessions. Its sturdy construction ensures durability, even in demanding conditions, making it a trusted companion for a wide array of forestry tasks.

Overall, the Poulan 961980019 stands out in the market for its blend of power, durability, and user-friendly design. Whether you're tackling yard work or professional projects, this chainsaw provides a versatile and efficient solution for all your cutting needs.
Top Page Image Contents