Poulan 961980019 Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 15

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure the on/off switch is in the OFF position.

2. Remove safety ignition key.

3. Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 18)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shoulder/shear bolt and hex nut. Should a for- eign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shoulder/shear bolt and spacer. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever is engaged, check to see if the capscrews have sheared. To replace the capscrew/shear bolts:

15

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4.Insert safety ignition and reconnect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

SPACER

 

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 18

TO REMOVE BELT COVER (See Fig. 19)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten securely.

 

BELT

 

COVER

FRAME

SCREWS

FIG. 19

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerSkid Plate Recoil auxiliary starter handle used for startingTo Control Snow Discharge See Figs HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Throw Snow See FigADD Gasoline See Fig Before Starting the EngineScraper BAR Check Engine OIL Level See FigSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Service Notes   413606X479 155377413607X479 Page 414280 Knob, Lever, Black 1724 KEY Part Description Repair Parts Drive Repair Parts Snow Thrower Model 961980019 96198001901 Drive Page KEY Part Description   KEY Part Description Limited Warranty

961980019 specifications

The Poulan 961980019 is a dependable and robust chainsaw designed for both novice and experienced users seeking an efficient tool for various cutting tasks. Renowned for its reliability and performance, this model is ideal for homeowners, landscapers, and woodworkers alike.

One of the standout features of the Poulan 961980019 is its powerful engine. Equipped with a reliable 42cc two-cycle engine, the chainsaw delivers strong cutting performance and consistent power, making it suitable for slicing through trees, logs, and other tough materials with ease. The engine's design ensures reduced emissions, promoting a more environmentally friendly operation without compromising on power.

The chainsaw features a 16-inch bar, providing a good balance between cutting capacity and maneuverability. This length is perfect for medium-sized tasks, allowing users to make efficient cuts without the weight of larger models. Coupled with a high chain speed, the Poulan 961980019 provides quick and clean cuts, enhancing productivity and efficiency in both home and professional settings.

Another notable characteristic is the chainsaw's lightweight construction. Weighing only 10 lbs, it minimizes user fatigue, making it easy to handle during extended use. The ergonomic design, featuring a comfortable grip and well-placed controls, ensures that users can operate the saw with confidence and ease.

The Poulan 961980019 also incorporates advanced technologies for enhanced safety and convenience. Its automatic chain oiling system provides continuous lubrication, which extends the life of the chain and bar while reducing wear and tear. Additionally, it includes a chain brake feature that helps protect users from kickback accidents, enhancing safety during operation.

The chainsaw is designed for easy maintenance, featuring a tool-less chain adjustment that allows users to make quick adjustments on the go. This means less downtime and more efficient work sessions. Its sturdy construction ensures durability, even in demanding conditions, making it a trusted companion for a wide array of forestry tasks.

Overall, the Poulan 961980019 stands out in the market for its blend of power, durability, and user-friendly design. Whether you're tackling yard work or professional projects, this chainsaw provides a versatile and efficient solution for all your cutting needs.
Top Page Image Contents