Poulan 961980019 owner manual Storage, Other

Page 17

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 21)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 21

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 2,134 meters. If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a Sears service centre/department.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a Sears service centre/de- partment, which has the proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Alcohol blended fuels (called gasohol or using ethanol or metha- nol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can dam- age the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour approximately one ounce (30 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/

17 exhaust area is still warm.

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYSkid Plate Recoil auxiliary starter handle used for startingStopping HOW to USE Your Snow ThrowerTo USE Choke Control See Fig To Control Snow Discharge See FigsTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigScraper BAR Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Service Notes   413607X479 413606X479155377 Page 414280 Knob, Lever, Black 1724 KEY Part Description Repair Parts Drive Repair Parts Snow Thrower Model 961980019 96198001901 Drive Page KEY Part Description   KEY Part Description Limited Warranty

961980019 specifications

The Poulan 961980019 is a dependable and robust chainsaw designed for both novice and experienced users seeking an efficient tool for various cutting tasks. Renowned for its reliability and performance, this model is ideal for homeowners, landscapers, and woodworkers alike.

One of the standout features of the Poulan 961980019 is its powerful engine. Equipped with a reliable 42cc two-cycle engine, the chainsaw delivers strong cutting performance and consistent power, making it suitable for slicing through trees, logs, and other tough materials with ease. The engine's design ensures reduced emissions, promoting a more environmentally friendly operation without compromising on power.

The chainsaw features a 16-inch bar, providing a good balance between cutting capacity and maneuverability. This length is perfect for medium-sized tasks, allowing users to make efficient cuts without the weight of larger models. Coupled with a high chain speed, the Poulan 961980019 provides quick and clean cuts, enhancing productivity and efficiency in both home and professional settings.

Another notable characteristic is the chainsaw's lightweight construction. Weighing only 10 lbs, it minimizes user fatigue, making it easy to handle during extended use. The ergonomic design, featuring a comfortable grip and well-placed controls, ensures that users can operate the saw with confidence and ease.

The Poulan 961980019 also incorporates advanced technologies for enhanced safety and convenience. Its automatic chain oiling system provides continuous lubrication, which extends the life of the chain and bar while reducing wear and tear. Additionally, it includes a chain brake feature that helps protect users from kickback accidents, enhancing safety during operation.

The chainsaw is designed for easy maintenance, featuring a tool-less chain adjustment that allows users to make quick adjustments on the go. This means less downtime and more efficient work sessions. Its sturdy construction ensures durability, even in demanding conditions, making it a trusted companion for a wide array of forestry tasks.

Overall, the Poulan 961980019 stands out in the market for its blend of power, durability, and user-friendly design. Whether you're tackling yard work or professional projects, this chainsaw provides a versatile and efficient solution for all your cutting needs.
Top Page Image Contents