Simplicity L8526EX, L9528EX, E95288E, L11532E, L10530EX, E105308E, E85268E After Each USE, Storage

Page 20

Operation

AFTER EACH USE

Normal use of the snowthrower may result in a build-up of packed snow in and around the starter cord housing and around engine controls. Heat from the engine will usually prevent the snow from freezing solid while the unit is running, but after the engine is shut down, some snow may continue melting from engine heat, and later freeze around some moving parts as the unit cools.

After each period of use, follow these steps to prevent freeze-up caused by ice formation in and around the engine controls and external parts.

1.Before shutting off the engine, pull the starter rope out 2 - 3 times, and allow it to rewind slowly. This will help clear packed snow from the starter cord area. Allow the engine to run for several minutes.

2.Stop the engine by moving the throttle lever (See Figure 1) down, turn the stop switch to the off position or by pulling out the engine key.

3.Brush snow and ice from the snowthrower. Be sure to clear engine and snowthrower controls, discharge chute, and chute rod gears, clutch cable areas, and anywhere else snow has accumulated.

4.Always remove the engine key and store in a safe place to prevent unauthorized use.

WARNING

Never store the unit (with fuel) in an enclosed, poorly ventilated structure. Fuel vapors can travel to an ignition source (such as a furnace, water heater, etc.) and cause an explosion.

Fuel vapor is also toxic to humans and animals.

5.If the snowthrower is kept in a cold shelter, fill the fuel tank to prevent condensation. Do not store near sparks or flame.

Note: The Engine Owner’s Manual contains further infor- mation on preventing ice formation and freeze-up.

WARNING

Never store the unit, with gasoline in engine or fuel tank, in a heated shelter or in enclosed, poorly ventilated enclosures. Gasoline fumes may reach an open flame, spark or pilot light (such as a furnace, water heater, clothes dryer, etc.) and cause an explosion.

Handle gasoline carefully. It is highly flammable and careless use could result in serious fire damage to your person or property.

Drain fuel into an approved container outdoors away from open flame or sparks.

STORAGE

WARNING

Never store the unit (with fuel) in an enclosed, poorly ventilated structure. Fuel vapors can travel to an ignition source (such as a furnace, water heater, etc.) and cause an explosion.

Fuel vapor is also toxic to humans and animals.

Before you store your unit for the off-season, read the Maintenance and Storage instructions in the Safety Rules section, then perform the following steps:

•Disengage the PTO, set the parking brake, and remove the key.

•Perform engine maintenance and storage measures listed in the engine owner’s manual. This includes draining the fuel system, or adding stabilizer to the fuel (do not store a fueled unit in an enclosed struc- ture - see warning).

Before starting the unit after it has been stored:

•Check all fluid levels. Check all maintenance items.

•Perform all recommended checks and procedures found in the engine owner’s manual.

•Allow the engine to warm up for several minutes before use.

17

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Print Vendor Instructions Operator’s ManualsPage OPERATOR’S Manual ModelsTable of Contents Safety Rules & Information Operating Safety Safety Rules and Information Moving PartsSafety Rules & Information TrainingSafety Rules ChildrenNorth American Model Decals DecalsDecals Chute Release Shift Decal ALL Model DecalsCE Model Decals Safety Icons Safety IconsIdentification Numbers CE Identification TAG MarkingsNorth American CE ModelsSpeed Selector Features, Controls, & OperationControl Locations Features & Controls Operation Checks Before Each START-UPManual Start Starting ControlsElectric Start Starting the Engine Operating the SnowthrowerClearing a Clogged Discharge Chute Will Continue until the Free-Hand Control is releasedGround Speed Selector Engine SpeedDeflector Scraper BAR & Skid ShoesEasy Turn Freewheeling Traction Drive Lock Full TractionEasy Turn Traction After Each USE StorageRegular Maintenance Maintenance ScheduleChecking Tire Pressure Auger Gear Case LubricationRegular Maintenance LubricationLubricate as shown in figure Lubricating the Auger Shaft & AssemblyCheck / Lubricate FREE-HAND Linkage Page Troubleshooting, Adjustments, Service TroubleshootingAuger does not stop when auger Auger rotates, but snow is notThrown far enough Poor tractionAdjustments Auger Drive AdjustmentTraction Drive Cable Adjustment Initial AdjustmentRun-In Adjustment 16 10.95cmEasy Turn Cable Adjustment Belt AdjustmentAuger Drive Belt Traction Drive BeltAdjustments & Service Shear PIN ReplacementBelt Guide Adjustment 3.18mmService Belt ReplacementSpout Rotator Rod Special Nut Cover Hair Pin Traction Belt Change Swing Plate Alignment Tabs Chassis SpecificationsEngine Parts & Accessories Replacement PartsMaintenance Items Technical ManualsO D U C T S

E115328E, L11532E, L10530EX, E95288E, 105308E specifications

The Simplicity L8526EX, L9528EX, 115328E, L9528E, and 95288E represent a line of advanced lawn mowers designed to combine efficiency with user-friendly features. Each model is tailored to meet diverse mowing needs, making them ideal for both residential and commercial applications.

The Simplicity L8526EX is renowned for its robust construction and exceptional cutting power. It features a powerful engine that ensures consistent performance even in challenging mowing conditions. One of its standout characteristics is the unique Mow More technology, which allows for smooth maneuverability and precise cutting, making it suitable for complex lawns with varying terrain. Additionally, its adjustable cutting heights provide flexibility, allowing users to select the perfect length for their grass.

The L9528EX is a versatile model designed for larger properties. It boasts a wider cutting deck, optimizing mowing time while reducing the number of passes required. The engine delivers high torque and speed, ensuring that grass is cut quickly and efficiently. This model also incorporates a sophisticated bagging system that efficiently collects clippings, preventing them from littering the lawn and providing a cleaner cut.

The 115328E model stands out for its ergonomic design and user-friendly controls. It features an innovative handle system that reduces vibration, enhancing comfort during prolonged use. Its easy-start technology ensures that users can get the mower running with minimal effort. With a robust frame and enhanced stability features, this model is built to last while offering superior cutting performance.

The L9528E model combines economy with high performance. It is lightweight yet durable, allowing for easy operation without compromising on power. The advanced mulching capability of this mower breaks down clippings finely, returning valuable nutrients back to the soil. This not only improves the health of the lawn but also minimizes the environmental impact.

Lastly, the 95288E is equipped with cutting-edge technologies for an ultimate mowing experience. It includes a digital display that provides real-time information on battery life and performance status. The easy-adjust mowing height system allows users to make quick adjustments on-the-fly. Additionally, it features a quiet operation mode ideal for residential areas, ensuring minimal disruption.

In summary, the Simplicity L8526EX, L9528EX, 115328E, L9528E, and 95288E showcase a commitment to quality, performance, and user satisfaction. Each model incorporates innovative features and technology that cater to a range of mowing requirements, making them valuable additions to any lawn care routine.
Top Page Image Contents