Simplicity E95288E, L9528EX, L11532E, L10530EX, E105308E, L8526EX, E85268E Service, Belt Replacement

Page 31

Service

BELT REPLACEMENT

Auger Drive Belt

The drive belts are of special construction and must be replaced with original factory replacement belts available from your nearest authorized service center. Some steps require the assistance of a second person. If the auger drive belt is damaged, the snow thrower will not discharge snow. Replace the damaged belt as follows.

1.Disconnect the spark plug wire.

2.Loosen the capscrews (A, Figure 25) on each side of the bottom panel (B).

3.Remove the bottom panel (B).

4.Loosen screw (B, Figure 21) from belt cover (A). Remove belt cover (A).

5.Loosen the belt guide (B, Figure 26). Pull the belt guide away from the auger drive pulley (A).

6.Pull the auger idler pulley (K) away from the auger drive belt (D) and slip the belt off of the idler.

7.Remove the auger drive belt (D) from the engine pul- ley. To remove the auger drive belt (D), the auger drive pulley (C) may have to be partially rotated.

8.Index or point the spout rotator to the center of the machine so the rotator control is in the center of the dash panel.

9.Remove special nut (A, Figure 27) and cover (B).

10.Remove hair pin (C) and slide rod forward about 3 inches. Until hex shaft separates from handle con- trol.

11.Remove the upper four capscrews (A, Figure 29) that hold together the auger housing (C) and the frame

(D). Loosen the lower two capscrews (B). The auger housing (C) and the frame (D) can now be split apart for removal of the belt.

12. .Remove the old auger drive belt (D, Figure 26) from the impeller pulley . Replace the auger drive belt with an original factory replacement belt available from an authorized service center.

13. .Install the new auger drive belt (D) onto the impeller pulley.

NOTE: To assemble the auger housing to the frame, have someone hold the auger clutch lever in the ENGAGED position. This will move the idler arm and pul- ley enough to allow the auger drive pulley to move back into position.

14.Assemble the auger housing (C, Figure 29) to the frame with the four upper capscrews (A) that were removed in step 11. Tighten the two lower capscrews

(B)

A

A

C

B

Figure 25. Bottom Cover

A.Capscrews

B.Bottom Panel

C.Auger Housing

 

 

A

 

 

B

 

 

F

 

L

C

 

 

 

 

D

 

K

E

 

 

 

 

A

J

 

G

 

I

 

 

 

H

Figure 26. Pulleys and Belts

A.Traction Drive Belt

B.Belt Guide

C.Auger Drive Pulley, Engine

D.Auger Drive Belt

E.Traction Drive Spring

F.Traction Drive Pulley, Engine

G.Traction Drive Pulley

H.Impeller Pulley

I.Swing Plate Axle Rod

J.“E”-Ring

K.Auger Idler Pulley

L.Traction Drive Idler Pulley

28

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Operator’s Manuals Print Vendor InstructionsPage Models OPERATOR’S ManualTable of Contents Safety Rules & Information Operating Safety Moving Parts Safety Rules and InformationTraining Safety Rules & InformationChildren Safety RulesDecals DecalsNorth American Model Decals CE Model Decals ALL Model DecalsChute Release Shift Decal Safety Icons Safety IconsCE Models Identification NumbersCE Identification TAG Markings North AmericanControl Locations Features, Controls, & OperationSpeed Selector Features & Controls Checks Before Each START-UP OperationElectric Start Starting ControlsManual Start Will Continue until the Free-Hand Control is released Starting the EngineOperating the Snowthrower Clearing a Clogged Discharge ChuteScraper BAR & Skid Shoes Ground Speed SelectorEngine Speed DeflectorEasy Turn Traction Full TractionEasy Turn Freewheeling Traction Drive Lock Storage After Each USEAuger Gear Case Lubrication Regular MaintenanceMaintenance Schedule Checking Tire PressureLubrication Regular MaintenanceCheck / Lubricate FREE-HAND Linkage Lubricating the Auger Shaft & AssemblyLubricate as shown in figure Page Troubleshooting Troubleshooting, Adjustments, ServicePoor traction Auger does not stop when augerAuger rotates, but snow is not Thrown far enoughInitial Adjustment AdjustmentsAuger Drive Adjustment Traction Drive Cable Adjustment16 10.95cm Run-In AdjustmentTraction Drive Belt Easy Turn Cable AdjustmentBelt Adjustment Auger Drive Belt3.18mm Adjustments & ServiceShear PIN Replacement Belt Guide AdjustmentBelt Replacement ServiceSpout Rotator Rod Special Nut Cover Hair Pin Traction Belt Change Swing Plate Alignment Tabs Engine SpecificationsChassis Technical Manuals Parts & AccessoriesReplacement Parts Maintenance ItemsO D U C T S

E115328E, L11532E, L10530EX, E95288E, 105308E specifications

The Simplicity L8526EX, L9528EX, 115328E, L9528E, and 95288E represent a line of advanced lawn mowers designed to combine efficiency with user-friendly features. Each model is tailored to meet diverse mowing needs, making them ideal for both residential and commercial applications.

The Simplicity L8526EX is renowned for its robust construction and exceptional cutting power. It features a powerful engine that ensures consistent performance even in challenging mowing conditions. One of its standout characteristics is the unique Mow More technology, which allows for smooth maneuverability and precise cutting, making it suitable for complex lawns with varying terrain. Additionally, its adjustable cutting heights provide flexibility, allowing users to select the perfect length for their grass.

The L9528EX is a versatile model designed for larger properties. It boasts a wider cutting deck, optimizing mowing time while reducing the number of passes required. The engine delivers high torque and speed, ensuring that grass is cut quickly and efficiently. This model also incorporates a sophisticated bagging system that efficiently collects clippings, preventing them from littering the lawn and providing a cleaner cut.

The 115328E model stands out for its ergonomic design and user-friendly controls. It features an innovative handle system that reduces vibration, enhancing comfort during prolonged use. Its easy-start technology ensures that users can get the mower running with minimal effort. With a robust frame and enhanced stability features, this model is built to last while offering superior cutting performance.

The L9528E model combines economy with high performance. It is lightweight yet durable, allowing for easy operation without compromising on power. The advanced mulching capability of this mower breaks down clippings finely, returning valuable nutrients back to the soil. This not only improves the health of the lawn but also minimizes the environmental impact.

Lastly, the 95288E is equipped with cutting-edge technologies for an ultimate mowing experience. It includes a digital display that provides real-time information on battery life and performance status. The easy-adjust mowing height system allows users to make quick adjustments on-the-fly. Additionally, it features a quiet operation mode ideal for residential areas, ensuring minimal disruption.

In summary, the Simplicity L8526EX, L9528EX, 115328E, L9528E, and 95288E showcase a commitment to quality, performance, and user satisfaction. Each model incorporates innovative features and technology that cater to a range of mowing requirements, making them valuable additions to any lawn care routine.
Top Page Image Contents