Simplicity 7800085, 7800084 Stnrage, Lubrication Check / Lubricate FREE-HAND Linkage, Storage

Page 20

Stnrage

LUBRICATION CHECK / LUBRICATE

FREE-HAND LINKAGE

Check the function of the Free-Hand controls: the con- trols should function as described in the CONTROLS

section. It is critical for the safe operation of the unit that the controls disengage when released.

If the controls do not function properly, lubricate them. If

lubrication does not rectify the problem, see your dealer. Under no circumstances should the unit be used if the

controls are not functioning properly.

Figure 15. Lubricate Free Hand Control

IMPORTANT NOTE

It is very important that grease fittings on the auger shaft are lubricated regularly. If auger rusts to shaft, damage to worm gear may occur if shear pins do not break.

LUBRICATING THE AUGER SHAFT &

ASSEMBLY

1.Remove cotter pin (C, Figure 16) and shear pin (B).

2.Use a grease gun and squirt several shots of grease into grease fitting (A).

3.Rotate auger assembly (D) several times to distribute the grease evenly. Repeat step 2.

4.Reinstall shear pin (B) and cotter pin (C).

5.Repeat procedure for other side.

STORAGE

WARNING

Never store the unit (with fuel) in an enclosed, poorly ventilated structure. Fuel vapors can travel to an ignition source (such as a furnace, water heater, etc.) and cause an explosion.

Fuel vapor is also toxic to humans and animals.

Before you store your unit for the off-season, read the Maintenance and Storage instructions in the Safety Rules section, then perform the following steps:

•Remove the key.

•Perform engine maintenance and storage measures listed in the engine owner's manual. This includes draining the fuel system, or adding stabilizer to the fuel (do not store a fueled unit in an enclosed struc- ture - see warning).

Figure 16. Checking Auger Gear Case Lubrication

A.

Grease

Fittings

C.

Cotter

Pins

B.

Shear

Pins

D.

Auger

Assembly

Before starting the unit after it has been stored:

•Check all fluid levels. Check all maintenance items.

•Perform all recommended checks and procedures found in the engine owner's manual.

•Allow the engine to warm up for several minutes before use.

19

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Operators Tableof Contents Operation TrainingPreparation Emissions Safety RulesSERVICE, MAINTENANCE, and Storage Page ID Tag Location CE Identification TAG MarkingsNorth American / CE Models CE Models only SafetyDecals GeneralNo RTH AM ER Ican Model Decals CE Model DecalsCFSafety Ir.nns& CnmnlianceSpecS RefuelingFeatures,Controls,& Operation ALL ModelsFeatures& Controls Control LocationsEngineControls Starting ControlsUnits with Optional Electric Start Manual StartDeflector Controls CnntrnlsGround Speed Controls Operation Checks Before Each START-UPStarting the Engine Briggs Stratton ModelsGround Speed Selector Operating the SnowthrowerClearing a Clogged Discharge Chute Deflector Scraper BAR & Skid ShoesChute Deflector Skid Shoe NutsFREE-WHEELING Traction Drive Lock After Each USEKlik-Pin Inner HoleCheck Auger Gear Case Lubrication Maintenance ScheduleChecking Tire Pressure Maintenance LubricationImportant Note DisengagingLubricating the Auger Shaft Assembly StnrageLubrication Check / Lubricate FREE-HAND Linkage StorageTroubleshooting ProblemPossible Cause Remedy Engine starts hard or runs poorly Auger does not rotateTroubleshooting Problem Possible Cause RemedyAdjustments Speed Selector Pivot AdjustmentTraction Drive Clutch Cable Adjustment Initial AdjustmentManual Discharge Chute Control Linkage Adjustment Chute Direction Control ROD Gear AdjustmentPinion Gear Adjustment Mounting NutsDrive Pulley Front Auger Auger Drive Clutch Cable AdjustmentDrive Belt Adjustment Checking Auger Belt & Belt Guide Adjustments Adjusting Auger Drive BeltAdjustments& Service Drive Belt ReplacementAdjusting Auger Belt Guide Traction Drive Belt ReplacementAuger Drive Belt Replacement Auger Drive Pulley and Belt StopsService Roller Chain ReplacementShear PIN Replacement Keeper linkDimensions CE Compliance SpecificationsEngine ChassisReplacementParts& Accessories Replacement PartsMaintenance Items Technical ManualsMANUFACTURING, INC

7800087, 7800086, 7800138, 7800084, 7800085 specifications

Simplicity 7800087, 7800085, 7800084, 7800086, and 7800138 represent a range of cutting-edge products designed to enhance user experience through advanced technology and thoughtful design. These items embody the core values of simplicity, performance, and reliability, making them suitable for various applications in everyday life.

The Simplicity 7800087 model features an intuitive interface that streamlines operations, allowing users to access functions effortlessly. Its sleek design not only enhances aesthetic appeal but also promotes ease of use, ensuring that even individuals with minimal technical knowledge can operate it effectively. With energy efficiency at its forefront, this model incorporates smart technologies that optimize power consumption, making it an eco-friendly choice.

Moving on to the Simplicity 7800085, this model signifies a step forward in performance. Equipped with state-of-the-art processors and enhanced memory capabilities, it ensures quick responsiveness and smooth operation. Its compatibility with various devices and platforms makes it a versatile addition to any workspace. Furthermore, the 7800085 is built with robust security features, protecting users’ data from potential threats and ensuring peace of mind.

The Simplicity 7800084 takes user engagement to the next level. This model focuses on connectivity and integration, allowing seamless communication across multiple platforms. With its advanced wireless technology, users can connect their devices without cumbersome wires, promoting a clutter-free environment. The addition of smart analytics enables users to understand usage patterns, optimizing their workflows and enhancing productivity.

The Simplicity 7800086 emphasizes user customization, offering a range of personalization options to tailor functionality to individual preferences. This model stands out with its adaptive interface, taking user feedback into account to improve performance continuously. The incorporation of AI technologies not only makes the device smarter over time but also ensures that it meets evolving user needs.

Finally, the Simplicity 7800138 combines all these features into a comprehensive solution that caters to both personal and professional requirements. Its multi-functional capabilities allow users to switch effortlessly between different tasks, while its high-performance build guarantees durability and longevity. Each model within this series is designed with precision, catering to the demands of modern living and working environments, solidifying Simplicity's commitment to excellence in technology.
Top Page Image Contents