Simplicity 7800086, 7800085 manual Adjustments, Speed Selector Pivot Adjustment, Initial Adjustment

Page 23

Adjustments

SPEED SELECTOR PIVOT ADJUSTMENT

Adjust as follows:

1.Move the ground speed control (A, Figure 17) fully forward.

2.Loosen the hardware (B) securing the upper and lower shift rods.

3.Push the lower rod (C) down fully (into the housing).

4.Make sure the ground speed control (A) is in the full forward (5th gear) position. Pull the two rods apart and tighten the shift rod hardware (B).

TRACTION DRIVE CLUTCH CABLE

ADJUSTMENT

Initial Adjustment

The traction drive clutch cable should initially be adjusted so that there is no slack in the cable when moved slightly from side to side, but bellcrank arm remains in fully down position. To adjust tension on the cable:

1.Loosen adjustment hex nut (Figure 18) by holding the adjusting flats and turning adjustment hex nut.

2.Tighten adjustment screw by turning adjustment flats and holding screw. The adjustment screw is a phillips screw and the head can be held or turned by inserting a screwdriver through the traction drive clutch cable spring. Tighten just until slack in cable is removed.

3.Tighten hex nut securely. The unit should able to be pushed forward and back freely.

WARNING

Do not over-tighten, as this may cause traction drive to engage without depressing the traction drive control (bellcrank arm must remain in down position).

Verify that the cables are not over-tightened: With speed selector in position 1 and traction drive control fully released, push snowthrower forward. The unit should move forward freely.

If unit does not move forward freely, the cable has been over-tightened. To remedy, loosen tension on clutch cable slightly, and recheck.

Figure 17. Speed Selector Linkage Adjustment

A. Ground Speed Lever

B.Shift Rod Hardware

C.Lower Shift Rod

_-_/_ __Traction

Drive

 

w_l_v.

Clutch Cable

i

_ . _

C____

Adjustment

'_4_._

I --

Flats

t _

 

.ex.at

 

_'_Adjustment

 

 

_Adjustment

r-

_Tr_oV_

Driv e

Traction

Drive

Clutch

Cable Spring

Bellcrank

Arm

 

 

Figure 18. Traction Drive Clutch Cable Adjustment

Run-In Adjustment

,After 5 hours of use, check for proper adjustment. Readjust clutch cable if necessary by increasing ten- sion on cable. A small amount of bellcrank arm movement is permissible if unit passes operating checks described in the Caution at left. Optimal adjustment provides 3/16" clearance between traction drive disc and rubber ring on friction disc when drive lever is released (see Figure 13 for fric- tion disk location).

22

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Operators Tableof Contents Operation TrainingPreparation Emissions Safety RulesSERVICE, MAINTENANCE, and Storage Page ID Tag Location CE Identification TAG MarkingsNorth American / CE Models CE Models only CE Model Decals SafetyDecalsGeneral No RTH AM ER Ican Model DecalsRefueling CFSafety Ir.nns& CnmnlianceSpecSALL Models Features,Controls,& OperationControl Locations Features& ControlsManual Start EngineControlsStarting Controls Units with Optional Electric StartDeflector Controls CnntrnlsGround Speed Controls Checks Before Each START-UP OperationBriggs Stratton Models Starting the EngineGround Speed Selector Operating the SnowthrowerClearing a Clogged Discharge Chute Skid Shoe Nuts DeflectorScraper BAR & Skid Shoes Chute DeflectorInner Hole FREE-WHEELING Traction Drive LockAfter Each USE Klik-PinCheck Auger Gear Case Lubrication Maintenance ScheduleChecking Tire Pressure Disengaging MaintenanceLubrication Important NoteStorage Lubricating the Auger Shaft AssemblyStnrage Lubrication Check / Lubricate FREE-HAND LinkageEngine starts hard or runs poorly Auger does not rotate TroubleshootingProblem Possible Cause RemedyProblem Possible Cause Remedy TroubleshootingInitial Adjustment AdjustmentsSpeed Selector Pivot Adjustment Traction Drive Clutch Cable AdjustmentMounting Nuts Manual Discharge Chute Control Linkage AdjustmentChute Direction Control ROD Gear Adjustment Pinion Gear AdjustmentDrive Pulley Front Auger Auger Drive Clutch Cable AdjustmentDrive Belt Adjustment Adjusting Auger Drive Belt Checking Auger Belt & Belt Guide AdjustmentsTraction Drive Belt Replacement Adjustments& ServiceDrive Belt Replacement Adjusting Auger Belt GuideAuger Drive Pulley and Belt Stops Auger Drive Belt ReplacementKeeper link ServiceRoller Chain Replacement Shear PIN ReplacementChassis DimensionsCE Compliance Specifications EngineTechnical Manuals ReplacementParts& AccessoriesReplacement Parts Maintenance ItemsMANUFACTURING, INC

7800087, 7800086, 7800138, 7800084, 7800085 specifications

Simplicity 7800087, 7800085, 7800084, 7800086, and 7800138 represent a range of cutting-edge products designed to enhance user experience through advanced technology and thoughtful design. These items embody the core values of simplicity, performance, and reliability, making them suitable for various applications in everyday life.

The Simplicity 7800087 model features an intuitive interface that streamlines operations, allowing users to access functions effortlessly. Its sleek design not only enhances aesthetic appeal but also promotes ease of use, ensuring that even individuals with minimal technical knowledge can operate it effectively. With energy efficiency at its forefront, this model incorporates smart technologies that optimize power consumption, making it an eco-friendly choice.

Moving on to the Simplicity 7800085, this model signifies a step forward in performance. Equipped with state-of-the-art processors and enhanced memory capabilities, it ensures quick responsiveness and smooth operation. Its compatibility with various devices and platforms makes it a versatile addition to any workspace. Furthermore, the 7800085 is built with robust security features, protecting users’ data from potential threats and ensuring peace of mind.

The Simplicity 7800084 takes user engagement to the next level. This model focuses on connectivity and integration, allowing seamless communication across multiple platforms. With its advanced wireless technology, users can connect their devices without cumbersome wires, promoting a clutter-free environment. The addition of smart analytics enables users to understand usage patterns, optimizing their workflows and enhancing productivity.

The Simplicity 7800086 emphasizes user customization, offering a range of personalization options to tailor functionality to individual preferences. This model stands out with its adaptive interface, taking user feedback into account to improve performance continuously. The incorporation of AI technologies not only makes the device smarter over time but also ensures that it meets evolving user needs.

Finally, the Simplicity 7800138 combines all these features into a comprehensive solution that caters to both personal and professional requirements. Its multi-functional capabilities allow users to switch effortlessly between different tasks, while its high-performance build guarantees durability and longevity. Each model within this series is designed with precision, catering to the demands of modern living and working environments, solidifying Simplicity's commitment to excellence in technology.
Top Page Image Contents