Simplicity 7800138, 7800085, 7800084, 7800086 Cnntrnls, Ground Speed Controls, Deflector Controls

Page 12

GROUND SPEED CONTROLS

A.Speed Selector - This lever (A, Figures 2 & 3) is used to set the ground speed of the snowthrower.

The snowthrower has five forward speeds, 1-5, and two reverse speeds, 1-2. No neutral position or gate is required, since the traction drive design automati- cally provides "neutral" (no forward or reverse move- ment), whenever the drive control is released.

B.Traction & Free Hand TM Control - This control engages the traction drive as the lever (B, Figures 2

& 3) is depressed, and disengages the traction drive when the lever is released. When both levers are

depressed the Free Hand TM control is activated. This allows the auger control to be released yet the auger remains engaged until the traction Free Hand TM is released. NOTE: Changing ground speeds must only be done while the drive control is in the disengaged (fully released) position.

AUGER CONTROL

C. Auger Control - The auger control clutch lever (C Figures 2 & 3), engages the auger drive when the lever is depressed and disengages the auger drive when the lever is released (unless Traction Free Hand TM control is also depressed-see above).

DEFLECTOR CONTROLS

D. Chute Direction Control - The chute direction con- trol (D, Figures 2 & 3), allows the discharge chute to be rotated to throw snow in the desired direction.

Snow may be thrown at any angle from straight left, to straight forward, to straight right.

E. Chute Deflector - Controls the distance snow is thrown. Tilting the chute deflector (E, Figure 3) UP provides a higher stream and greater distance, while

tilting the deflector DOWN provides a lower stream and less distance.

F. Chute Deflector Knob - This knob (F, Figure 3) allows the discharge chute deflector (E) to be locked in the desired tilt position.

SCRAPER HEIGHT

G, H. Scraper Bar Height Control - The skid shoes (G, Figure 3) control the height of the scraper bar (H). (NOTE: On later models, the scraper bar is also adjustable.) The scraper bar allows smooth surfaces (such as concrete or asphalt driveways) to be scraped clean of snow. On surfaces such as gravel, the scraper bar should be adjusted higher -- so that it will not pick up gravel or debris.

Cnntrnls

Figure 2. Operator's Control Position

A.

Speed

Selector

C.Auger

Control

B.

Drive

Control

D.Chute

Direction Control

%

 

 

 

®

 

Figure 3.

Snowthrower

Controls

 

 

A. Speed

Selector

E. Chute

Deflector

B. Drive

Control

F. Chute

Deflector Knob

C. Auger

Control

G. Skid Shoes

D. Chute

Control Knob

H. Scraper

Bar

 

 

I. Traction

Lock Pins

TRACTION LOCK CONTROL

Traction Lock Pins - The traction drive to each wheel can be locked and unlocked with the traction

lock pins (I, Figure 3) to permit the unit to "free-

wheel','allowing easier manual handling and transport of the snowthrower.

11

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operators Tableof Contents Training PreparationOperation Safety Rules SERVICE, MAINTENANCE, and StorageEmissions Page CE Identification TAG Markings North American / CE Models CE Models onlyID Tag Location SafetyDecals GeneralNo RTH AM ER Ican Model Decals CE Model DecalsCFSafety Ir.nns& CnmnlianceSpecS RefuelingFeatures,Controls,& Operation ALL ModelsFeatures& Controls Control LocationsEngineControls Starting ControlsUnits with Optional Electric Start Manual StartCnntrnls Ground Speed ControlsDeflector Controls Operation Checks Before Each START-UPStarting the Engine Briggs Stratton ModelsOperating the Snowthrower Clearing a Clogged Discharge ChuteGround Speed Selector Deflector Scraper BAR & Skid ShoesChute Deflector Skid Shoe NutsFREE-WHEELING Traction Drive Lock After Each USEKlik-Pin Inner HoleMaintenance Schedule Checking Tire PressureCheck Auger Gear Case Lubrication Maintenance LubricationImportant Note DisengagingLubricating the Auger Shaft Assembly StnrageLubrication Check / Lubricate FREE-HAND Linkage StorageTroubleshooting ProblemPossible Cause Remedy Engine starts hard or runs poorly Auger does not rotateTroubleshooting Problem Possible Cause RemedyAdjustments Speed Selector Pivot AdjustmentTraction Drive Clutch Cable Adjustment Initial AdjustmentManual Discharge Chute Control Linkage Adjustment Chute Direction Control ROD Gear AdjustmentPinion Gear Adjustment Mounting NutsAuger Drive Clutch Cable Adjustment Drive Belt AdjustmentDrive Pulley Front Auger Checking Auger Belt & Belt Guide Adjustments Adjusting Auger Drive BeltAdjustments& Service Drive Belt ReplacementAdjusting Auger Belt Guide Traction Drive Belt ReplacementAuger Drive Belt Replacement Auger Drive Pulley and Belt StopsService Roller Chain ReplacementShear PIN Replacement Keeper linkDimensions CE Compliance SpecificationsEngine ChassisReplacementParts& Accessories Replacement PartsMaintenance Items Technical ManualsMANUFACTURING, INC

7800087, 7800086, 7800138, 7800084, 7800085 specifications

Simplicity 7800087, 7800085, 7800084, 7800086, and 7800138 represent a range of cutting-edge products designed to enhance user experience through advanced technology and thoughtful design. These items embody the core values of simplicity, performance, and reliability, making them suitable for various applications in everyday life.

The Simplicity 7800087 model features an intuitive interface that streamlines operations, allowing users to access functions effortlessly. Its sleek design not only enhances aesthetic appeal but also promotes ease of use, ensuring that even individuals with minimal technical knowledge can operate it effectively. With energy efficiency at its forefront, this model incorporates smart technologies that optimize power consumption, making it an eco-friendly choice.

Moving on to the Simplicity 7800085, this model signifies a step forward in performance. Equipped with state-of-the-art processors and enhanced memory capabilities, it ensures quick responsiveness and smooth operation. Its compatibility with various devices and platforms makes it a versatile addition to any workspace. Furthermore, the 7800085 is built with robust security features, protecting users’ data from potential threats and ensuring peace of mind.

The Simplicity 7800084 takes user engagement to the next level. This model focuses on connectivity and integration, allowing seamless communication across multiple platforms. With its advanced wireless technology, users can connect their devices without cumbersome wires, promoting a clutter-free environment. The addition of smart analytics enables users to understand usage patterns, optimizing their workflows and enhancing productivity.

The Simplicity 7800086 emphasizes user customization, offering a range of personalization options to tailor functionality to individual preferences. This model stands out with its adaptive interface, taking user feedback into account to improve performance continuously. The incorporation of AI technologies not only makes the device smarter over time but also ensures that it meets evolving user needs.

Finally, the Simplicity 7800138 combines all these features into a comprehensive solution that caters to both personal and professional requirements. Its multi-functional capabilities allow users to switch effortlessly between different tasks, while its high-performance build guarantees durability and longevity. Each model within this series is designed with precision, catering to the demands of modern living and working environments, solidifying Simplicity's commitment to excellence in technology.
Top Page Image Contents