Simplicity 7800086, 7800085 manual Auger Drive Belt Replacement, Auger Drive Pulley and Belt Stops

Page 28

DRIVE BELT REPLACEMENT (Cont.)

Traction Drive Belt Replacement (Cont.)

5.Reverse the procedure to install the new belt. Be

sure there are no twists in the belt, and that the belt is properly seated in the pulley grooves.

6.Replace the belt cover.

7.Start the unit, and check the traction drive for proper operation. See "Traction Clutch Cable Adjustment" for adjustment procedures.

Auger Drive Belt Replacement

1.Remove gas from fuel tank and run engine until it stops running from lack of fuel.

2.Disconnect spark plug wire and fasten it away from the spark plug.

3.Remove belt cover (See Figure 23).

4.Loosen auger belt guide and slide belt off engine pul- ley and away from idler pulley. (See Figure 26).

5.Clamp or tie auger control lever to handle in the fully depressed position to release all tension on the auger pulley brake pad, and provide clearance for belt removal.

6.Tilt unit forward and rest on auger housing.

7.Remove lower cover.

8.Loosen hex screw securing belt stop (Figure 28), and pivot the belt stop away from the pulley to permit removal of belt.

9.Pull the belt out of the unit, and install the new belt on the auger drive pulley.

10.Position belt stop to provide 1/8" clearance between stop and belt, and and tighten securely.

11.Replace lower cover.

12.Return unit to normal upright operating position.

13.Release auger control.

14.Install auger belt over engine pulley.

15.Adjust auger belt stop as described under ADJUST-

ING BELT GUIDES.

16.Install belt cover.

17.Connect spark plug wire and fill fuel tank.

18.Start unit and check auger for proper operation. See "Auger Drive Clutch Cable Adjustment" for adjust- ment procedures if additional adjustment is neces- sary.

Service

WARNING

Auger must NOT rotate unless the Auger Control lever has been depressed, and auger must stop within 5 seconds after Auger Control lever has been released.

WARNING

Do not go near the discharge chute or auger

when the engine is running. Do not run the engine with any cover or guard removed.

ger Drive Pulley

Figure 28. Auger Drive Pulley and Belt Stops

27

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Operators Tableof Contents Preparation TrainingOperation SERVICE, MAINTENANCE, and Storage Safety RulesEmissions Page North American / CE Models CE Models only CE Identification TAG MarkingsID Tag Location SafetyDecals GeneralNo RTH AM ER Ican Model Decals CE Model DecalsCFSafety Ir.nns& CnmnlianceSpecS RefuelingFeatures,Controls,& Operation ALL ModelsFeatures& Controls Control LocationsEngineControls Starting ControlsUnits with Optional Electric Start Manual StartGround Speed Controls CnntrnlsDeflector Controls Operation Checks Before Each START-UPStarting the Engine Briggs Stratton ModelsClearing a Clogged Discharge Chute Operating the SnowthrowerGround Speed Selector Deflector Scraper BAR & Skid ShoesChute Deflector Skid Shoe NutsFREE-WHEELING Traction Drive Lock After Each USEKlik-Pin Inner HoleChecking Tire Pressure Maintenance ScheduleCheck Auger Gear Case Lubrication Maintenance LubricationImportant Note DisengagingLubricating the Auger Shaft Assembly StnrageLubrication Check / Lubricate FREE-HAND Linkage StorageTroubleshooting ProblemPossible Cause Remedy Engine starts hard or runs poorly Auger does not rotateTroubleshooting Problem Possible Cause RemedyAdjustments Speed Selector Pivot AdjustmentTraction Drive Clutch Cable Adjustment Initial AdjustmentManual Discharge Chute Control Linkage Adjustment Chute Direction Control ROD Gear AdjustmentPinion Gear Adjustment Mounting NutsDrive Belt Adjustment Auger Drive Clutch Cable AdjustmentDrive Pulley Front Auger Checking Auger Belt & Belt Guide Adjustments Adjusting Auger Drive BeltAdjustments& Service Drive Belt ReplacementAdjusting Auger Belt Guide Traction Drive Belt ReplacementAuger Drive Belt Replacement Auger Drive Pulley and Belt StopsService Roller Chain ReplacementShear PIN Replacement Keeper linkDimensions CE Compliance SpecificationsEngine ChassisReplacementParts& Accessories Replacement PartsMaintenance Items Technical ManualsMANUFACTURING, INC

7800087, 7800086, 7800138, 7800084, 7800085 specifications

Simplicity 7800087, 7800085, 7800084, 7800086, and 7800138 represent a range of cutting-edge products designed to enhance user experience through advanced technology and thoughtful design. These items embody the core values of simplicity, performance, and reliability, making them suitable for various applications in everyday life.

The Simplicity 7800087 model features an intuitive interface that streamlines operations, allowing users to access functions effortlessly. Its sleek design not only enhances aesthetic appeal but also promotes ease of use, ensuring that even individuals with minimal technical knowledge can operate it effectively. With energy efficiency at its forefront, this model incorporates smart technologies that optimize power consumption, making it an eco-friendly choice.

Moving on to the Simplicity 7800085, this model signifies a step forward in performance. Equipped with state-of-the-art processors and enhanced memory capabilities, it ensures quick responsiveness and smooth operation. Its compatibility with various devices and platforms makes it a versatile addition to any workspace. Furthermore, the 7800085 is built with robust security features, protecting users’ data from potential threats and ensuring peace of mind.

The Simplicity 7800084 takes user engagement to the next level. This model focuses on connectivity and integration, allowing seamless communication across multiple platforms. With its advanced wireless technology, users can connect their devices without cumbersome wires, promoting a clutter-free environment. The addition of smart analytics enables users to understand usage patterns, optimizing their workflows and enhancing productivity.

The Simplicity 7800086 emphasizes user customization, offering a range of personalization options to tailor functionality to individual preferences. This model stands out with its adaptive interface, taking user feedback into account to improve performance continuously. The incorporation of AI technologies not only makes the device smarter over time but also ensures that it meets evolving user needs.

Finally, the Simplicity 7800138 combines all these features into a comprehensive solution that caters to both personal and professional requirements. Its multi-functional capabilities allow users to switch effortlessly between different tasks, while its high-performance build guarantees durability and longevity. Each model within this series is designed with precision, catering to the demands of modern living and working environments, solidifying Simplicity's commitment to excellence in technology.
Top Page Image Contents