Snapper L1530EX, L1428EX, L11226EX, L1632E, L1226EX, 1632EX manual Features & Controls

Page 12

Features & Controls

Speed Selector

Selects forward speeds 1-6 and reverse speeds 1-2. No neutral position or gate is required, since the traction drive design automatically provides "neutral" (no forward or reverse movement), whenever the Drive Control is released.

Traction Control / Free Hand™ Lock

Engages traction drive to wheels when depressed. Also locks auger control when depressed simultaneously. Releasing the traction control lever releases the Free Hand™ auger control lock and stops the drive wheels and auger.

Auger Control

Engages the auger/impeller when depressed. Releasing the control stops the auger/impeller.

Chute Direction Control

Push the lever forward to unlock the rotator control. Moving the lever to the left will turn the spout to the left side and moving the lever to the right will rotate the spout to the right side. Releasing the lever locks the spout in position.

Remote Deflector Control

Chute Deflector: Locks chute deflector in desired posi- tion. Tilting the chute deflector UP provides a higher stream and greater distance, while tilting the deflector DOWN provides a lower stream and less distance.

Easy Turn™ Control

Easy Turn Control: Engaging the Easy Turn™ lever releases the left wheel to allow easy turning in tight areas. Releasing the control automatically engages both drive wheels for full traction.

Traction Lock Pins: (1100 Series Only) The right trac- tion wheel can be completely released using the locking pin (see Figure 9). This allows the unit to be easily moved with the engine off.

Starter

Electric Start: Depressing the starter button activates the electric starter. The electric start button operates on 120 Volts AC, which is provided by connection to the extension cord provided. Connect this extension cord ONLY to a properly grounded 3 prong electrical outlet.

Recoil Starter (All Models): Pulling the recoil handle

cranks the engine.

Fuel

Fuel tank filler cap (see illustration). Note: The fuel shut off valve is located under the fuel tank or on the front of the engine. Close the valve when the snowthrower is not in use. Open the valve before starting. Fill tank to approximately 1.5 in. (38 mm) below top of neck to allow for fuel expansion.

Primer Button

When pressed, the primer button provides initial fuel to help start a cold engine. Normally, pressing the primer button twice will provide enough fuel to start a cold engine.

Throttle Lever (Optional)

Controls engine speed. Move toward the hare icon for faster engine speed, move toward the turtle icon for slower engine speed. Move the throttle all the way to STOP the engine. Set the throttle to FAST (hare icon) for operation.

Engine Key

The engine key prevents the engine from being started. The key must be fully inserted into the key slot for the unit to start. The key can also used to stop the engine by pulling the key out of the key slot.

Choke Knob

The choke knob adjusts the air/fuel mixture, and is used to help start a cold engine by providing a richer mixture. Once the engine is warm and running smoothly, the choke knob should be set to the off position to provide a normal air/fuel mix.

Stop Switch (Optional)

Turn the the switch to the ON position to operate the engine. Turn the switch to the OFF position to stop the engine.

Headlight (Select Models, Not Pictured)

The headlight is on at all times when the engine is run- ning.

11

Image 12
Contents OPERATOR’S Manual ModelsTable of Contents Safety Rules & Information Operating Safety Safety Rules & Information Moving PartsTraining Ignition System C a l s DecalsNorth American Model Decals ALL Model Decals CE Model DecalsChute Release Shift Decal Safety Icons Safety IconsId entification Numbers CE Identification TAG MarkingsNorth American CE ModelsFeatures, Controls, & Operation Control LocationsFeatures & Controls E r a t i o n Checks Before Each START-UPStarting Controls Electric StartManual Start Snow Series MaxStarting the Engine E r a t i o n Stopping the EngineOperating the Snowthrower Clearing a Clogged Discharge ChuteWill Continue until the Free-Hand Control is released Ground Speed Selector Engine SpeedDeflector Scraper BAR & Skid ShoesFull Traction Easy Turn TractionEasy Turn Freewheeling and Traction Drive Lock After Each USE StoragePage Maintenance Schedule Checking Tire PressureAuger Gear Case Lubrication Regular Maintenance LubricationLubricate Auger Shaft Assembly Check / Lubricate FREE-HAND LinkageLubricate as shown in Figure Troubleshooting Problem Possible Cause RemedyWhen drive lever is released Auger rotates, but snow is notThrown far enough Poor tractionAuger Drive Adjustment Traction Drive Cable AdjustmentInitial Adjustment J u s t m e n t sAdjustments Run-In Adjustment16 10.95cm Easy Turn Cable Adjustment Belt AdjustmentAuger Drive Belt Traction Drive BeltAdjustments & Service Shear PIN ReplacementBelt Guide Adjustment 3.18 mmBelt Replacement R v i c eSpout Rotator Rod Special Nut Cover Hair Pin Traction Belt Change Swing Plate Alignment Tabs Dimensions EngineChassis Series Briggs & StrattonReplacement Parts Maintenance ItemsTechnical Manuals O D U C T S

L1428EX, L1226EX, L1632E, L1530EX, 1632EX specifications

The Snapper L series of lawn mowers, including models L11226EX, L1428E, L1530E, 1632E, and 1632EX, represent a perfect blend of innovation, efficiency, and durability for both residential and commercial applications. Each model comes equipped with unique features and cutting-edge technologies designed to enhance user experience and improve lawn care results.

Starting with the L11226EX, this model features a powerful engine that ensures optimal performance while cutting through grass with precision. It boasts a 26-inch cutting deck, providing a wide cutting path for faster mowing sessions. The inclusion of an adjustable height feature allows users to easily customize the mowing height to achieve their desired lawn finish. Another key feature is its easy-to-use self-propulsion system, which makes navigating uneven terrain a breeze.

The L1428E model is notable for its eco-friendly electric engine, reducing emissions while maintaining a quiet operation. It features a compact 28-inch deck, making it perfect for maneuvering through tight spaces and small yards. The ergonomic design enhances comfort and control, making longer mowing sessions less tiring. Additionally, it includes a rapid charge system, ensuring minimal downtime between uses.

Moving on to the L1530E, this model capitalizes on an efficient battery technology that delivers consistent power. Equipped with a 30-inch deck, it strikes a balance between maneuverability and coverage. The model's innovative grass collection system ensures minimal clumping, providing a neat finish. Moreover, its lightweight design allows for easy handling and transport.

The 1632E model is designed for those looking for robust performance coupled with advanced technology. With a 32-inch cutting deck, it excels in larger properties while maintaining excellent cutting quality. Its dual-blade system provides a clean cut and promotes healthy grass growth. The mower's user-friendly dashboard features intuitive controls, allowing operators to switch between modes efficiently.

Lastly, the 1632EX variant comes with enhanced features, including an intuitive smart-cut technology that intelligently adjusts the mower's speed based on grass thickness. This ensures optimal energy consumption while achieving superior cutting results. This model also includes a sturdy build that withstands tough conditions, along with oversized rear wheels for increased stability and traction.

Overall, each of these Snapper L series mowers is engineered with performance, comfort, and eco-responsibility in mind, making them excellent choices for any lawn care enthusiast. Whether tackling small yards or large properties, these mowers deliver the reliability and efficiency required for superior lawn maintenance.