Snapper L1226EX, L1428EX, L11226EX, L1530EX, L1632E, 1632EX manual Starting the Engine

Page 15

O p e r a t i o n

STARTING THE ENGINE

WARNING

Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go. Broken bones, fractures, bruises or sprains could result. When starting engine, pull the starter cord slowly until resistance is felt and then pull rapidly to avoid kickback.

WARNING

Gasoline and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. When starting the engine, ensure that spark plug, muffler, fuel cap and air cleaner are in place and secured. Do not crank engine with spark plug removed. If engine floods, set choke (if equipped) to open/run position.

CAUTION

This engine was shipped from Briggs & Stratton without oil. Before you start the engine, make sure you add oil according to the instructions in the Engine Owner’s Manual. If you start the engine without oil, it will be damaged beyond repair and will not be covered under warranty.

1.Check the oil level. See “How To Check/Add Oil” section in Engine Owner’s Manual.

2.Make sure equipment drive controls, if equipped, are disengaged. See the equipment manual for location and operation of these controls.

3.Push the stop switch (A, Figure 2), if equipped, to the ON position.

Or move the throttle control lever (A, Figure 3), if equipped, to the FAST position. Operate the engine with the throttle control lever in the FAST position.

WARNING

Engines give off carbon monoxide, an odorless, colorless, poison gas. Breathing carbon monox- ide can cause nausea, fainting or death. When starting the engine, start and run engine out- doors. Do not start or run engine in enclosed area, even if doors or windows are open.

A

Figure 2. Engine Start/Stop

A. Stop Switch

WARNING

Unintentional sparking can result in fire or elec- tric shock.

Unintentional start-up can result in entanglement, traumatic amputation, or laceration.

•Use a 3-wire extension cord.

•First attach extension cord to electric starter connector and then into a wall receptacle. If additional extension cord is required, use a 3- wire.

•If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

4.Turn the fuel shut-off valve (B, Figure 3), if equipped, to the ON position.

5.Push in the safety key (C).

6.Turn the choke control knob (D) to the choke posi- tion.

NOTE: Do not use the choke to start a warm engine.

7. Push the primer button (E) two times.

NOTE: Do not use the primer to start a warm engine.

8.Rewind Start: Firmly hold the starter cord handle

(F). Pull the starter cord slowly until resistance is felt, then pull rapidly.

NOTE: If the engine does not start after three attempts, see the “Troubleshooting” section in the Engine Owner’s Manual.

14

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Models OPERATOR’S ManualTable of Contents Safety Rules & Information Operating Safety Moving Parts Safety Rules & InformationTraining Ignition System C a l s DecalsNorth American Model Decals ALL Model Decals CE Model DecalsChute Release Shift Decal Safety Icons Safety IconsCE Models Id entification NumbersCE Identification TAG Markings North AmericanControl Locations Features, Controls, & OperationFeatures & Controls Checks Before Each START-UP E r a t i o nSnow Series Max Starting ControlsElectric Start Manual StartStarting the Engine Stopping the Engine E r a t i o nOperating the Snowthrower Clearing a Clogged Discharge ChuteWill Continue until the Free-Hand Control is released Scraper BAR & Skid Shoes Ground Speed SelectorEngine Speed DeflectorFull Traction Easy Turn TractionEasy Turn Freewheeling and Traction Drive Lock Storage After Each USEPage Maintenance Schedule Checking Tire PressureAuger Gear Case Lubrication Lubrication Regular MaintenanceLubricate Auger Shaft Assembly Check / Lubricate FREE-HAND LinkageLubricate as shown in Figure Problem Possible Cause Remedy TroubleshootingPoor traction When drive lever is releasedAuger rotates, but snow is not Thrown far enoughJ u s t m e n t s Auger Drive AdjustmentTraction Drive Cable Adjustment Initial AdjustmentAdjustments Run-In Adjustment16 10.95cm Traction Drive Belt Easy Turn Cable AdjustmentBelt Adjustment Auger Drive Belt3.18 mm Adjustments & ServiceShear PIN Replacement Belt Guide AdjustmentR v i c e Belt ReplacementSpout Rotator Rod Special Nut Cover Hair Pin Traction Belt Change Swing Plate Alignment Tabs Series Briggs & Stratton DimensionsEngine ChassisReplacement Parts Maintenance ItemsTechnical Manuals O D U C T S

L1428EX, L1226EX, L1632E, L1530EX, 1632EX specifications

The Snapper L series of lawn mowers, including models L11226EX, L1428E, L1530E, 1632E, and 1632EX, represent a perfect blend of innovation, efficiency, and durability for both residential and commercial applications. Each model comes equipped with unique features and cutting-edge technologies designed to enhance user experience and improve lawn care results.

Starting with the L11226EX, this model features a powerful engine that ensures optimal performance while cutting through grass with precision. It boasts a 26-inch cutting deck, providing a wide cutting path for faster mowing sessions. The inclusion of an adjustable height feature allows users to easily customize the mowing height to achieve their desired lawn finish. Another key feature is its easy-to-use self-propulsion system, which makes navigating uneven terrain a breeze.

The L1428E model is notable for its eco-friendly electric engine, reducing emissions while maintaining a quiet operation. It features a compact 28-inch deck, making it perfect for maneuvering through tight spaces and small yards. The ergonomic design enhances comfort and control, making longer mowing sessions less tiring. Additionally, it includes a rapid charge system, ensuring minimal downtime between uses.

Moving on to the L1530E, this model capitalizes on an efficient battery technology that delivers consistent power. Equipped with a 30-inch deck, it strikes a balance between maneuverability and coverage. The model's innovative grass collection system ensures minimal clumping, providing a neat finish. Moreover, its lightweight design allows for easy handling and transport.

The 1632E model is designed for those looking for robust performance coupled with advanced technology. With a 32-inch cutting deck, it excels in larger properties while maintaining excellent cutting quality. Its dual-blade system provides a clean cut and promotes healthy grass growth. The mower's user-friendly dashboard features intuitive controls, allowing operators to switch between modes efficiently.

Lastly, the 1632EX variant comes with enhanced features, including an intuitive smart-cut technology that intelligently adjusts the mower's speed based on grass thickness. This ensures optimal energy consumption while achieving superior cutting results. This model also includes a sturdy build that withstands tough conditions, along with oversized rear wheels for increased stability and traction.

Overall, each of these Snapper L series mowers is engineered with performance, comfort, and eco-responsibility in mind, making them excellent choices for any lawn care enthusiast. Whether tackling small yards or large properties, these mowers deliver the reliability and efficiency required for superior lawn maintenance.
Top Page Image Contents