Snapper L1428EX, L11226EX, L1530EX, L1632E Troubleshooting, Problem Possible Cause Remedy

Page 25

Troubleshooting, Adjustments, & Service

TROUBLESHOOTING

WARNING

This section provides troubleshooting and service instructions. Locate the problem and check the possible cause/remedy in the order listed.

Also, refer to the Engine Owner’s Manual for additional information.

For problems not covered here, contact your local deal- er.

Before performing any adjustment or service to snowthrower, stop the engine and wait for mov- ing parts to stop. Remove the key. To prevent accidental starting, disconnect the spark plug wire and fasten away from the plug.

Problem

Possible Cause

Remedy

 

 

 

Engine fails to start.

Key is OFF.

Push key in to the ON position.

 

 

 

 

Failure to prime cold engine

Press primer button twice and

 

 

restart.

 

 

 

 

Fuel valve is in CLOSED position.

Turn valve to OPEN position.

 

 

 

 

Out of fuel.

Fill fuel tank.

 

 

 

 

Choke OFF - cold engine.

Turn choke to ON, set throttle to

 

 

FAST.

 

 

 

 

Engine flooded.

Turn choke to OFF; try starting.

 

 

 

 

No spark.

Check gap. Gap plug, clean elec-

 

 

trode, or replace plug as necessary.

 

 

 

 

Water in fuel, or old fuel.

Drain tank. (Dispose of fuel at an

 

 

authorized hazardous waste facility.)

 

 

Fill with fresh fuel.

 

 

 

Engine starts hard or runs poorly.

Fuel mixture too rich.

Move choke to OFF position.

 

 

 

 

Carburetor adjusted incorrectly.

See your dealer for adjustments.

 

 

 

 

Spark plug faulty, fouled, or gapped

Clean and gap, or replace.

 

improperly.

 

 

 

 

 

Fuel cap vent is blocked.

Clear vent.

 

 

 

Scraper bar does not clean hard

Skid shoes improperly adjusted.

RAISE skid shoes (this lowers the

surface.

 

scraper bar).

 

 

 

 

Skid shoes improperly adjusted.

LOWER skid shoes (this raises the

 

 

scraper bar.)

 

 

 

Auger does not rotate.

Auger control not engaged.

Engage auger control.

 

 

 

 

Foreign matter blocking auger.

STOP engine and REMOVE the

 

 

key. DISCONNECT the spark plug

 

 

wire. Clear auger using clean-out

 

 

tool. See warning in SAFETY

 

 

RULES.

 

 

 

 

Auger drive clutch cable slack.

Tighten to remove slack. See auger

 

 

clutch cable adjustment.

 

 

 

 

Auger drive belt slipping.

Check auger drive belt adjustment.

 

 

 

 

Broken belt.

Replace belt.

 

 

 

 

Shear pin broken.

Replace shear pin.

 

 

 

24

Image 25
Contents Models OPERATOR’S ManualTable of Contents Safety Rules & Information Operating Safety Moving Parts Safety Rules & InformationTraining Ignition System Decals C a l sNorth American Model Decals CE Model Decals ALL Model DecalsChute Release Shift Decal Safety Icons Safety IconsCE Identification TAG Markings Id entification NumbersNorth American CE ModelsControl Locations Features, Controls, & OperationFeatures & Controls Checks Before Each START-UP E r a t i o nElectric Start Starting ControlsManual Start Snow Series MaxStarting the Engine Stopping the Engine E r a t i o nClearing a Clogged Discharge Chute Operating the SnowthrowerWill Continue until the Free-Hand Control is released Engine Speed Ground Speed SelectorDeflector Scraper BAR & Skid ShoesEasy Turn Traction Full TractionEasy Turn Freewheeling and Traction Drive Lock Storage After Each USEPage Checking Tire Pressure Maintenance ScheduleAuger Gear Case Lubrication Lubrication Regular MaintenanceCheck / Lubricate FREE-HAND Linkage Lubricate Auger Shaft AssemblyLubricate as shown in Figure Problem Possible Cause Remedy TroubleshootingAuger rotates, but snow is not When drive lever is releasedThrown far enough Poor tractionTraction Drive Cable Adjustment Auger Drive AdjustmentInitial Adjustment J u s t m e n t sRun-In Adjustment Adjustments16 10.95cm Belt Adjustment Easy Turn Cable AdjustmentAuger Drive Belt Traction Drive BeltShear PIN Replacement Adjustments & ServiceBelt Guide Adjustment 3.18 mmR v i c e Belt ReplacementSpout Rotator Rod Special Nut Cover Hair Pin Traction Belt Change Swing Plate Alignment Tabs Engine DimensionsChassis Series Briggs & StrattonMaintenance Items Replacement PartsTechnical Manuals O D U C T S

L1428EX, L1226EX, L1632E, L1530EX, 1632EX specifications

The Snapper L series of lawn mowers, including models L11226EX, L1428E, L1530E, 1632E, and 1632EX, represent a perfect blend of innovation, efficiency, and durability for both residential and commercial applications. Each model comes equipped with unique features and cutting-edge technologies designed to enhance user experience and improve lawn care results.

Starting with the L11226EX, this model features a powerful engine that ensures optimal performance while cutting through grass with precision. It boasts a 26-inch cutting deck, providing a wide cutting path for faster mowing sessions. The inclusion of an adjustable height feature allows users to easily customize the mowing height to achieve their desired lawn finish. Another key feature is its easy-to-use self-propulsion system, which makes navigating uneven terrain a breeze.

The L1428E model is notable for its eco-friendly electric engine, reducing emissions while maintaining a quiet operation. It features a compact 28-inch deck, making it perfect for maneuvering through tight spaces and small yards. The ergonomic design enhances comfort and control, making longer mowing sessions less tiring. Additionally, it includes a rapid charge system, ensuring minimal downtime between uses.

Moving on to the L1530E, this model capitalizes on an efficient battery technology that delivers consistent power. Equipped with a 30-inch deck, it strikes a balance between maneuverability and coverage. The model's innovative grass collection system ensures minimal clumping, providing a neat finish. Moreover, its lightweight design allows for easy handling and transport.

The 1632E model is designed for those looking for robust performance coupled with advanced technology. With a 32-inch cutting deck, it excels in larger properties while maintaining excellent cutting quality. Its dual-blade system provides a clean cut and promotes healthy grass growth. The mower's user-friendly dashboard features intuitive controls, allowing operators to switch between modes efficiently.

Lastly, the 1632EX variant comes with enhanced features, including an intuitive smart-cut technology that intelligently adjusts the mower's speed based on grass thickness. This ensures optimal energy consumption while achieving superior cutting results. This model also includes a sturdy build that withstands tough conditions, along with oversized rear wheels for increased stability and traction.

Overall, each of these Snapper L series mowers is engineered with performance, comfort, and eco-responsibility in mind, making them excellent choices for any lawn care enthusiast. Whether tackling small yards or large properties, these mowers deliver the reliability and efficiency required for superior lawn maintenance.