Snapper L1428EX, L11226EX, L1530EX, L1632E, L1226EX E r a t i o n, Checks Before Each START-UP

Page 13

O p e r a t i o n

GENERAL OPERATION

CHECKS BEFORE EACH START-UP

1.Make sure all safety guards are in place and all nuts, bolts and clips are secure.

2.Check to make sure that the clean-out is attached to the auger housing. Do not operate the machine with- out the clean-out tool properly stored on the auger housing.

3.Check the engine oil level. See your engine owner’s manual for procedure and specifications.

4.Check to make sure spark plug wire is attached and spark plug is tightened securely. If necessary, torque spark plug to 15 ft. lbs.

5.Check the fuel supply. Fill the tank no closer than 1/4 to 1/2 inch of top of tank to provide space for expan- sion. See your engine owner’s manual for fuel recom- mendations.

6.Check the scraper bar to make sure it is set at the desired height. Adjust the skid shoes if necessary.

7.Check the drive control (B, Figure 5), and auger con- trol (C) for proper operation. If adjustment is required, see the service section for procedures.

8.Check the chute direction control (D, Figure 5) for proper operation. The discharge chute should rotate freely in both directions. See the service section for adjustment procedures and troubleshooting.

9.Check the chute deflector (E, Figure 5) for proper operation. The deflector should pivot freely up and down.

10.Position the chute at the desired starting direction and set the deflector at the desired angle.

11.Check the speed selector (A, Figure 5) for smooth operation. The control must move freely into each speed position gate and remain in position when released. If the speed selector does not move freely into all forward and reverse speed positions, contact your local authorized dealer for assistance.

WARNING

This unit is a “two-stage” snowthrower.

The first stage is the auger, which feeds the snow back into the impeller housing. The second stage is the impeller, which throws the snow out the discharge chute. If bodily contact is made with the auger or impeller when they are rotating, severe personal injury will occur.

To avoid injury, keep others and yourself away from the auger and the discharge chute whenever the engine is running. Read and follow all of the safety rules and warnings in this manual.

DANGER

Do not clean out discharge chute with hands. Contact with moving parts inside chute will cause serious injury. Use clean out tool provided with machine. Use the following procedure to remove objects or clear the chute:

1.Stop the engine. Remove the key.

2.Wait 10 seconds to be sure the auger/impeller blades have stopped rotating.

3.Always use the clean-out tool. DO NOT use your hands.

WARNING

For your safety, operation on slopes should be in an up and down direction only. If it becomes nec- essary to move across the face of a slope, use caution and do not blow snow. Be very careful when changing direction on a slope.

Proper winter footwear is recommended for the operator to help prevent slipping. Never attempt to clean snow from excessively steep slopes. The maximum slope for any operation is 17.7% (10º).

WARNING

Gasoline is highly flammable and must be han- dled with care. Never fill the tank when the engine is hot or running. Always move outdoors to fill the tank. Keep snowthrower and gasoline away from open flame or spark.

12

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Models OPERATOR’S ManualTable of Contents Safety Rules & Information Operating Safety Moving Parts Safety Rules & InformationTraining Ignition System Decals C a l sNorth American Model Decals CE Model Decals ALL Model DecalsChute Release Shift Decal Safety Icons Safety IconsCE Identification TAG Markings Id entification NumbersNorth American CE ModelsControl Locations Features, Controls, & OperationFeatures & Controls Checks Before Each START-UP E r a t i o nElectric Start Starting ControlsManual Start Snow Series MaxStarting the Engine Stopping the Engine E r a t i o nClearing a Clogged Discharge Chute Operating the SnowthrowerWill Continue until the Free-Hand Control is released Engine Speed Ground Speed SelectorDeflector Scraper BAR & Skid ShoesEasy Turn Traction Full TractionEasy Turn Freewheeling and Traction Drive Lock Storage After Each USEPage Checking Tire Pressure Maintenance ScheduleAuger Gear Case Lubrication Lubrication Regular MaintenanceCheck / Lubricate FREE-HAND Linkage Lubricate Auger Shaft AssemblyLubricate as shown in Figure Problem Possible Cause Remedy TroubleshootingAuger rotates, but snow is not When drive lever is releasedThrown far enough Poor tractionTraction Drive Cable Adjustment Auger Drive AdjustmentInitial Adjustment J u s t m e n t sRun-In Adjustment Adjustments16 10.95cm Belt Adjustment Easy Turn Cable AdjustmentAuger Drive Belt Traction Drive BeltShear PIN Replacement Adjustments & ServiceBelt Guide Adjustment 3.18 mmR v i c e Belt ReplacementSpout Rotator Rod Special Nut Cover Hair Pin Traction Belt Change Swing Plate Alignment Tabs Engine DimensionsChassis Series Briggs & StrattonMaintenance Items Replacement PartsTechnical Manuals O D U C T S

L1428EX, L1226EX, L1632E, L1530EX, 1632EX specifications

The Snapper L series of lawn mowers, including models L11226EX, L1428E, L1530E, 1632E, and 1632EX, represent a perfect blend of innovation, efficiency, and durability for both residential and commercial applications. Each model comes equipped with unique features and cutting-edge technologies designed to enhance user experience and improve lawn care results.

Starting with the L11226EX, this model features a powerful engine that ensures optimal performance while cutting through grass with precision. It boasts a 26-inch cutting deck, providing a wide cutting path for faster mowing sessions. The inclusion of an adjustable height feature allows users to easily customize the mowing height to achieve their desired lawn finish. Another key feature is its easy-to-use self-propulsion system, which makes navigating uneven terrain a breeze.

The L1428E model is notable for its eco-friendly electric engine, reducing emissions while maintaining a quiet operation. It features a compact 28-inch deck, making it perfect for maneuvering through tight spaces and small yards. The ergonomic design enhances comfort and control, making longer mowing sessions less tiring. Additionally, it includes a rapid charge system, ensuring minimal downtime between uses.

Moving on to the L1530E, this model capitalizes on an efficient battery technology that delivers consistent power. Equipped with a 30-inch deck, it strikes a balance between maneuverability and coverage. The model's innovative grass collection system ensures minimal clumping, providing a neat finish. Moreover, its lightweight design allows for easy handling and transport.

The 1632E model is designed for those looking for robust performance coupled with advanced technology. With a 32-inch cutting deck, it excels in larger properties while maintaining excellent cutting quality. Its dual-blade system provides a clean cut and promotes healthy grass growth. The mower's user-friendly dashboard features intuitive controls, allowing operators to switch between modes efficiently.

Lastly, the 1632EX variant comes with enhanced features, including an intuitive smart-cut technology that intelligently adjusts the mower's speed based on grass thickness. This ensures optimal energy consumption while achieving superior cutting results. This model also includes a sturdy build that withstands tough conditions, along with oversized rear wheels for increased stability and traction.

Overall, each of these Snapper L series mowers is engineered with performance, comfort, and eco-responsibility in mind, making them excellent choices for any lawn care enthusiast. Whether tackling small yards or large properties, these mowers deliver the reliability and efficiency required for superior lawn maintenance.
Top Page Image Contents