Sears 486.248463 owner manual Assembling the Belts, Drive Belt, Auger Belt, Viewed from Rear

Page 12

ASSEMBLING THE BELTS

IMPORTANT: The tapered "V" section of the belts must be seated into the grooves of the V-pulleys.

DRIVE BELT

Remove the two outside 1/8" hairpin clips which are assembled to the L.H. and R.H. tension adjusting chains outside of the clutch idler assembly frame. (The clips will be reinstalled after both belts have been assembled.) Do not remove the 3/32" hairpin clips assembled to the chains on the inside of the assembly frame. See fi gure 21.

Assemble the drive belt onto the tractor's engine pulley and then onto the upper rear pulley on the clutch/idler assembly. Keep the fl at idler pulley on the outside of the belt. See fi gure 21.

Hold this diagram above you while viewing the Clutch/Idler Assembly from underneath the tractor. Right and left in this diagram will be the reverse of the viewer's right and left.

AUGER BELT

Make sure the auger belt is correctly assembled to the snow thrower. The belt must pass over the top of the auger pulley and then twist 1/4 turn to pass underneath the two side idler pulleys on the snow thrower. The "V" side of the belt must seat in the grooves of all three pulleys. See fi gure 22.

 

AUGER PULLEY

TWIST

TWIST

1/4 TURN

1/4 TURN

IDLER

IDLER

PULLEY

PULLEY

RIGHT SIDE

ENGINE

LEFT SIDE

FIGURE 22

VIEWED FROM REAR

 

 

OF TRACTOR

PULLEY

OF TRACTOR

 

 

FLAT

 

DRIVE V-BELT

 

 

IDLER

 

 

 

 

PULLEY

 

 

 

 

1/8"

HAIRPIN CLIP

1/8"

HAIRPIN CLIP

FIGURE 21

VIEWED FROM UNDERNEATH

12

Image 12
Contents 46- 2 Stage Snow Thrower Tractor Attachment Table of Contents WarrantyAccessories and Attachments Safety Hardware Package Contents Assembly Carton ContentsTools Required for Assembly Removal of Parts from CartonTractor Preparation Items Removed from TractorLeft Side View Right Side View Left Side ViewThis page for tractors with 54 mower decks only Mower DecksAttaching CLUTCH/IDLER Assembly Engine Pulleys Less than 6 in DiameterTractors with 54 Mower Decks only Assembly of Snow Thrower Mounting Snow Thrower to Tractor Right Front Corner ViewAssembling the Belts Drive BeltAuger Belt Viewed from RearAttaching Weight Tray to Tractor Checklist AccessoriesHOW to Start Your Snow Thrower HOW to Stop Your Snow ThrowerOperation Know Your Snow ThrowerHOW to USE Your Snow Thrower Operating TipsControlling Snow Discharge Raising and LoweringMaintenance Service and Adjustments Lift Release Cable AdjustmentSkid SHOE, Leveling Shoe Adjustment Replacing Auger BeltTroubleshooting Removing the Spiral Auger HousingStorage Storage RecommendationsParts QTY Description Part 554 51 59 58 30 2968 QTY Description Page Page Page Slope Guide Get it fixed, at your home or ours

486.248463 specifications

The Sears 486.248463 is a notable piece of computing history, representing the transitional phase in personal computing during the early 1990s. This device embodies the era when home and office computers began to embrace more advanced capabilities, driven largely by the evolution of processor technology and user requirements.

At the heart of the Sears 486.248463 is the Intel 486 processor, a significant leap from its predecessors. This microprocessor, which debuted in 1989, introduced a new level of performance, allowing users to handle more complex applications and multitasking functions seamlessly. The 486 architecture included an integrated floating-point unit, enhancing its ability to perform mathematical calculations, which was particularly beneficial for graphic design and engineering applications.

The Sears 486.248463 boasts a robust memory capacity, typically equipped with 4 to 16 MB of RAM, allowing for efficient operation of various software applications. This level of RAM was innovative for its time, providing users the ability to run multiple programs concurrently without experiencing slowdowns. Additionally, the system could support hard drives ranging from 120 MB to 1 GB, catering to the growing need for data storage as software applications became more sophisticated.

Another key feature of this model was its compatibility with DOS and early Windows operating systems. Users could enjoy a graphical user interface while leveraging the power of DOS-based applications, marking a significant shift in user experience. The Sears 486.248463 also included expansion slots, which allowed for upgrades and customization. Users could add additional memory or enhance graphics capabilities, reflecting the growing trend of personalized computing.

Graphics capabilities were enhanced through the inclusion of VGA support, delivering improved visual fidelity for both productivity applications and gaming. The resolution provided by VGA allowed for clearer images and more vibrant colors, making it suitable for a variety of multimedia tasks.

In terms of connectivity, the Sears 486.248463 featured standard serial and parallel ports, enabling connections to printers, modems, and other peripherals. This flexibility made it a suitable choice for both home users and small business environments.

Overall, the Sears 486.248463 stands as a representative of its time, showcasing key technologies and characteristics that laid the foundation for modern personal computing. Its combination of performance, expandability, and compatibility highlights how far technology has come and the significant milestones achieved throughout computing history.