Sears 486.248463 owner manual Operation, Know Your Snow Thrower, Before Starting

Page 15

OPERATION

KNOW YOUR SNOW THROWER

Read this owner's manual and safety rules before operating your snow thrower.

Compare the illustration below with your snow thrower to familiarize yourself with the various controls and their locations.

LIFT RELEASE TRIGGER

CHUTE TILT HANDLE

LIFT HANDLE

 

UPPER CHUTE

CRANK ROD

 

LOWER CHUTE

 

LEVELING SHOE (Behind housing)

SCRAPER PLATE

SPIRAL AUGERS, R.H. & L.H.

CHUTE TILT HANDLE Pivots the Upper Chute up or down to control the angle and distance of discharge. CRANK ROD Rotates the Lower and Upper Chutes to control the direction of discharge.

LEVELING SHOE Helps maintain the snow thrower in a level position.

LIFT HANDLE Used to lift or lower the snow thrower to transport or operating position.

LIFT RELEASE TRIGGER Releases the lock which holds the snow thrower in the up, transport position.

SKID SHOE

UPPER AND LOWER DISCHARGE CHUTE Controls direction and height of snow discharge.

SCRAPER PLATE Replaceable plate that absorbs wear and impact from contact with ground.

SKID SHOE Controls amount of clearance between the scraper plate and the ground.

SPIRAL AUGER, R.H. & L.H. Feed snow to the impeller fan at the center of the housing.

BEFORE STARTING

•Use the end of assembly checklist to verify that all instructions have been properly completed.

•Make sure the skid shoes are adjusted to maintain adequate ground clearance between the snow thrower and the type of surface to be cleared. The skid shoes are factory adjusted for clearing a smooth surface. (Refer to the Service and Adjustments section in this manual.)

•Make sure the tractor engine has the correct oil for winter operation. Refer to your tractor owner's manual.

HOW TO START YOUR SNOW THROWER

•The tractor should be sitting with the engine running at full throttle. Pull the attachment clutch switch out to the engaged position, starting the snow thrower before starting the tractor in motion.

HOW TO STOP YOUR SNOW THROWER

•To stop the snow thrower, push in the attachment clutch switch on the tractor. Refer to the Operation section in your tractor owner's manual.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 46- 2 Stage Snow Thrower Tractor Attachment Table of Contents WarrantyAccessories and Attachments Safety Hardware Package Contents Carton Contents AssemblyItems Removed from Tractor Tools Required for AssemblyRemoval of Parts from Carton Tractor PreparationRight Side View Left Side View Left Side ViewMower Decks This page for tractors with 54 mower decks onlyAttaching CLUTCH/IDLER Assembly Engine Pulleys Less than 6 in DiameterTractors with 54 Mower Decks only Assembly of Snow Thrower Right Front Corner View Mounting Snow Thrower to TractorViewed from Rear Assembling the BeltsDrive Belt Auger BeltAttaching Weight Tray to Tractor Accessories ChecklistKnow Your Snow Thrower HOW to Start Your Snow ThrowerHOW to Stop Your Snow Thrower OperationRaising and Lowering HOW to USE Your Snow ThrowerOperating Tips Controlling Snow DischargeMaintenance Replacing Auger Belt Service and AdjustmentsLift Release Cable Adjustment Skid SHOE, Leveling Shoe AdjustmentStorage Recommendations TroubleshootingRemoving the Spiral Auger Housing StorageParts QTY Description Part 554 51 59 58 30 2968 QTY Description Page Page Page Slope Guide Get it fixed, at your home or ours

486.248463 specifications

The Sears 486.248463 is a notable piece of computing history, representing the transitional phase in personal computing during the early 1990s. This device embodies the era when home and office computers began to embrace more advanced capabilities, driven largely by the evolution of processor technology and user requirements.

At the heart of the Sears 486.248463 is the Intel 486 processor, a significant leap from its predecessors. This microprocessor, which debuted in 1989, introduced a new level of performance, allowing users to handle more complex applications and multitasking functions seamlessly. The 486 architecture included an integrated floating-point unit, enhancing its ability to perform mathematical calculations, which was particularly beneficial for graphic design and engineering applications.

The Sears 486.248463 boasts a robust memory capacity, typically equipped with 4 to 16 MB of RAM, allowing for efficient operation of various software applications. This level of RAM was innovative for its time, providing users the ability to run multiple programs concurrently without experiencing slowdowns. Additionally, the system could support hard drives ranging from 120 MB to 1 GB, catering to the growing need for data storage as software applications became more sophisticated.

Another key feature of this model was its compatibility with DOS and early Windows operating systems. Users could enjoy a graphical user interface while leveraging the power of DOS-based applications, marking a significant shift in user experience. The Sears 486.248463 also included expansion slots, which allowed for upgrades and customization. Users could add additional memory or enhance graphics capabilities, reflecting the growing trend of personalized computing.

Graphics capabilities were enhanced through the inclusion of VGA support, delivering improved visual fidelity for both productivity applications and gaming. The resolution provided by VGA allowed for clearer images and more vibrant colors, making it suitable for a variety of multimedia tasks.

In terms of connectivity, the Sears 486.248463 featured standard serial and parallel ports, enabling connections to printers, modems, and other peripherals. This flexibility made it a suitable choice for both home users and small business environments.

Overall, the Sears 486.248463 stands as a representative of its time, showcasing key technologies and characteristics that laid the foundation for modern personal computing. Its combination of performance, expandability, and compatibility highlights how far technology has come and the significant milestones achieved throughout computing history.
Top Page Image Contents