Sears 486.248463 HOW to USE Your Snow Thrower, Operating Tips, Controlling Snow Discharge

Page 16

HOW TO USE YOUR SNOW THROWER

CAUTION: Never direct discharge towards bystanders or windows. Do not allow anyone in front of unit.

CONTROLLING SNOW DISCHARGE

•To control the direction snow is thrown, the discharge chute has 180 degrees of rotation. Turn the crank rod clockwise to rotate the chute to the right. Turn the crank rod counterclockwise to rotate the chute to the left.

•To control the distance snow is thrown, the upper section of the discharge chute pivots up and down. Push forward on the chute tilt handle to pivot the chute down, decreasing the distance snow is thrown. Pull back on the handle to pivot the chute up, increasing the distance snow is thrown.

RAISING AND LOWERING

•To raise, push down on the lift handle until the snow thrower locks in the raised transport position.

•To lower, push down slightly on the lift handle and pull the trigger. With the trigger pulled, slowly lower the snow thrower until it reaches the ground.

CAUTION: Do not operate the snow thrower without the rear weight attached to the tractor to provide extra traction and stability.

REMOVING SNOW

Snow removal conditions vary greatly from light fl uffy snowfall to wet heavy snow. Operating instructions must be fl exible to fi t the conditions encountered. The operator must adapt the lawn tractor and snow thrower to depth of snow, wind direction, temperature and surface conditions.

•Before beginning operation, thoroughly inspect the area of operation and remove all door mats, sleds, boards, wires and other foreign objects.

•The spiral auger speed is directly related to engine speed. For maximum snow removal and discharge, maintain high engine r.p.m. (full throttle). It is advisable to operate the lawn tractor at a slow ground speed (1st gear) for safe and effi cient snow removal.

•In deep, drifted or banked snow it will be necessary to use full throttle and a slow ground speed (1st gear). Drive forward into the snow, depress the tractor's clutch-brake pedal and allow the spiral auger to clear the snow. Repeat this method until a path is cleared. On the second pass, overlap the fi rst enough to allow the snow thrower to handle the snow without repeated stopping and starting of forward motion.

•In extremely deep snow, raise the snow thrower from the ground to remove the top layer and drive forward only until the tractors front tires reach the uncleared bottom layer of snow. Depress the tractor's clutch- brake pedal and allow the spiral auger to clear the snow. Reverse the tractor and lower the snow thrower to the ground. Drive the tractor forward until the snow again becomes too deep. Repeating this process into and out of drifts will eventually clear even the deepest of snow piles.

•If the snow thrower becomes clogged with snow or jammed with a foreign object, disengage the snow thrower immediately and shut off the tractor engine. Unclog the snow thrower before resuming operation.

DANGER: Shut off engine and disengage snow thrower before unclogging discharge chute. Unclog using a wooden stick, not your hands.

OPERATING TIPS

•Discharge snow down wind whenever possible.

•To help prevent snow from sticking to the snow thrower, allow the snow thrower to reach outdoor temperature before using it. A light coat of wax may also be applied to the inside surface of the snow thrower housing and discharge chute.

•Use tire chains to improve traction.

•Use rear wheel weights to improve traction.

•Before the fi rst snowfall, remove all stones, sticks and other objects which could become hidden by the snow. Permanent obstacles should be marked for visibility.

•Overlap each pass slightly to assure complete snow removal.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 46- 2 Stage Snow Thrower Tractor Attachment Warranty Table of ContentsAccessories and Attachments Safety Hardware Package Contents Assembly Carton ContentsTools Required for Assembly Removal of Parts from CartonTractor Preparation Items Removed from TractorLeft Side View Right Side View Left Side ViewThis page for tractors with 54 mower decks only Mower DecksEngine Pulleys Less than 6 in Diameter Attaching CLUTCH/IDLER AssemblyTractors with 54 Mower Decks only Assembly of Snow Thrower Mounting Snow Thrower to Tractor Right Front Corner ViewAssembling the Belts Drive BeltAuger Belt Viewed from RearAttaching Weight Tray to Tractor Checklist AccessoriesHOW to Start Your Snow Thrower HOW to Stop Your Snow ThrowerOperation Know Your Snow ThrowerHOW to USE Your Snow Thrower Operating TipsControlling Snow Discharge Raising and LoweringMaintenance Service and Adjustments Lift Release Cable AdjustmentSkid SHOE, Leveling Shoe Adjustment Replacing Auger BeltTroubleshooting Removing the Spiral Auger HousingStorage Storage RecommendationsParts QTY Description Part 554 51 59 58 30 2968 QTY Description Page Page Page Slope Guide Get it fixed, at your home or ours

486.248463 specifications

The Sears 486.248463 is a notable piece of computing history, representing the transitional phase in personal computing during the early 1990s. This device embodies the era when home and office computers began to embrace more advanced capabilities, driven largely by the evolution of processor technology and user requirements.

At the heart of the Sears 486.248463 is the Intel 486 processor, a significant leap from its predecessors. This microprocessor, which debuted in 1989, introduced a new level of performance, allowing users to handle more complex applications and multitasking functions seamlessly. The 486 architecture included an integrated floating-point unit, enhancing its ability to perform mathematical calculations, which was particularly beneficial for graphic design and engineering applications.

The Sears 486.248463 boasts a robust memory capacity, typically equipped with 4 to 16 MB of RAM, allowing for efficient operation of various software applications. This level of RAM was innovative for its time, providing users the ability to run multiple programs concurrently without experiencing slowdowns. Additionally, the system could support hard drives ranging from 120 MB to 1 GB, catering to the growing need for data storage as software applications became more sophisticated.

Another key feature of this model was its compatibility with DOS and early Windows operating systems. Users could enjoy a graphical user interface while leveraging the power of DOS-based applications, marking a significant shift in user experience. The Sears 486.248463 also included expansion slots, which allowed for upgrades and customization. Users could add additional memory or enhance graphics capabilities, reflecting the growing trend of personalized computing.

Graphics capabilities were enhanced through the inclusion of VGA support, delivering improved visual fidelity for both productivity applications and gaming. The resolution provided by VGA allowed for clearer images and more vibrant colors, making it suitable for a variety of multimedia tasks.

In terms of connectivity, the Sears 486.248463 featured standard serial and parallel ports, enabling connections to printers, modems, and other peripherals. This flexibility made it a suitable choice for both home users and small business environments.

Overall, the Sears 486.248463 stands as a representative of its time, showcasing key technologies and characteristics that laid the foundation for modern personal computing. Its combination of performance, expandability, and compatibility highlights how far technology has come and the significant milestones achieved throughout computing history.
Top Page Image Contents