ENGLISH
out of its place of storage. In this case ensure the door to the storage place is open. Exhaust fumes are toxic.
•Never drive across a slope. Move from the top down, and from the bottom to the top. Be careful when changing direction on a slope. Avoid steep slopes.
•Never operate the machine with insufficient protection or without the safety devices in place.
•Existing safety devices must not be disconnected or disengaged.
•Do not alter the engine’s regulator setting and do not race the engine. The possibility of personal injury increases when the engine is run at high revs.
•Never use the snow thrower near enclosures, cars, windowpanes, slopes etc. without properly setting the discharge chute deflector.
•Always keep children away from areas to be cleared. Get another adult to keep the children under supervision.
•Do not overload the machine by driving it too fast.
•Take care when reversing. Look behind you before and during reversing to check for any obstacles.
•Never point the discharge chute towards bystanders. Do not allow anyone to stand in front of the machine.
•Disengage the auger when the snow thrower is to be transported or is not in use Do not drive too fast on slippery surfaces when transporting.
•Only use accessories that are approved by the machine’s manufacturer.
•Never drive the snow thrower in bad visibility or without satisfactory lighting.
•Always ensure you have a good balance and a tight grip on the handle.
•Never use the snow thrower on a roof.
•Do not touch engine components because they are warm during use. Risk of burn injuries.
2.4MAINTENANCE AND STORAGE
•Tighten all nuts and screws so that the machine is in safe working condition. Check the shear bolts regularly.
•Always use genuine spare parts.
•Never store the machine with petrol in the tank in buildings where the fumes can come into contact with open flames or sparks.
•Allow the engine to cool before putting the machine in store.
•Before a long storage, check the instructions for recommendations.
•Replace damaged warning and instruction stickers.
•Let the engine run a couple of minutes with the auger connected after use. This prevents the auger from freezing solid.
3 ASSEMBLY
Note: Instructions to the left and right sides start from the driving position behind the snow thrower.
3.1CONTENTS - OUTER PACKING
The packing contains: - One snow thrower
- One adjustment lever - One gear rod
- One discharge chute
- One set of instructions - One assembly kit
3.2UNPACKING
1.Remove all loose items from the carton.
2.Cut off the plastic straps holding the adjustment lever and the gear rod.
3.Cut the four corners of the carton and let the sides fall down.
4.Unscrew the screws (X) that fasten the shoes to the bedding. See fig. 1.
5.Roll the snow thrower from the carton.
6.Cut the plastic tape holding the control wires on the underside of the handle.
3.3HANDLE, SEE FIG. 2, 3
1.Hook on the auger and drive wires
2.Assemble the handle with the following parts: A Four Screws
B Two Support plates for the upper screws C Two Washers for the lower screws
3.Tighten the four screws.
3.4SNOW DISCHARGE CHUTE, SEE FIG. 4
1.Place the discharge chute (D) on the flange against the worm gear.
2.Mount the three carriage pieces (E) with two screws each.
3.Tighten properly.
3.5ADJUSTMENT LEVER, SEE FIG. 5
1. Assemble the eyebolt (F) in the handle.
2.Insert the shaft end into the plastic bushing and adapt the worm gear to the recesses in the discharge chute.
3.Lock the joint with the locking pin (G).
4.Check the discharge chute by turning it fully in both directions. The chute should rotate freely.
3.6GEAR LEVER, SEE FIG. 6
Assemble the gear lever to the gearbox shaft as follows:
1.Set up the machine on the auger housing and set the ger lever (H) in the first gear forwards. See fig. 6.
2.Assemble the screw (I) through the angle joint and shaft. Tighten the screw.
3.Tighten the upper screw (T) between the gear lever and the angle joint.
4.Tighten the lower screw (U) between the gear lever and the angle joint.
41