Operating Your Snow Thrower, Starting The Engine

SECTION 4: OPERATING YOUR SNOW THROWER

Before Starting

WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.

Gas & Oil Fill-Up

Service the engine with gasoline and oil as instructed in the Tecumseh Engines manual packed separately with your snow thrower. Read instructions carefully.

WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.

•A small plastic cup may be located inside the fuel fill opening beneath the gas cap. Remove and discard this cup before filling up the tank.

WARNING: If your home electrical

system is grounded, but a three-hole receptacle is not available, do not use your snow thrower’s electric starter.

If you have a grounded three-prong receptacle, proceed as follows:

•Plug the extension cord into the outlet located on the engine’s surface. Plug the other end of extension cord into a three-prong 120-volt, grounded, AC outlet in a well-ventilated area.

•Rotate choke control to FULL choke position (cold engine start).

NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL.

•Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing.

NOTE: DO NOT use primer to restart a warm engine after a short shutdown.

Starting The Engine

•Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug wire (inside the rubber boot) is fastened securely over the metal tip on the spark plug.

•Make certain both the auger control and drive control are in the disengaged (released) position.

•Move throttle control up to FAST position. Insert ignition key into slot. Make sure it snaps into place. Do not attempt to turn the key.

NOTE: The engine cannot start unless the key is inserted into ignition switch.

Electric Starter

•Determine that your home’s wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain.

CAUTION: If your home’s wiring system

is not a three-wire grounded system, do not use this electric starter under any conditions.

WARNING: The optional electric starter is equipped with a grounded three-wire power cord and plug, and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three-prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter.

•Push starter button to start engine.

•Once the engine starts, immediately release starter button.

•As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to FULL and then slowly into the OFF position again.

•When disconnecting the extension cord, always unplug the end at the three-prong wall outlet before unplugging the opposite end from the snow thrower.

Recoil Starter

•Rotate choke control to FULL choke position (cold engine start).

NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL.

•Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing.

NOTE: DO NOT use primer to restart a warm engine after a short shutdown.

NOTE: Additional priming may be necessary if the temperature is below 15° Fahrenheit.

•Grasp the recoil starter handle and slowly pull the rope out. At the point where it becomes slightly harder to pull the rope, slowly allow the rope to recoil.

7524, 9528 specifications

The Troy-Bilt 9528 and 7524 are popular snow blowers engineered to tackle winter's toughest challenges. With robust features and advanced technologies, these machines are designed for both residential and light commercial use, ensuring efficient snow removal for homeowners and businesses alike.

One of the defining characteristics of these models is their powerful engines. The 9528 is equipped with a 277cc engine, while the 7524 features a 208cc engine. Both engines provide the necessary power to handle heavy snowfall and deliver optimal performance even in the harshest winter conditions. The electric start capability on these models adds convenience, allowing users to start the machines with just the push of a button.

The build quality of the Troy-Bilt 9528 and 7524 is impressive, featuring a durable steel construction that enhances their longevity and reliability. Their rugged auger systems, designed for maximum snow intake, work in tandem with a strong impeller to efficiently throw snow far away from the path, reducing the need for multiple passes.

User-friendly controls are another highlight of these snow blowers. The models come with an easy-to-use dashboard that allows operators to adjust speed and chute direction with minimal effort. The power steering feature on the 9528 facilitates maneuverability, enabling users to navigate tight spots and challenging landscapes with ease.

In addition, both machines are equipped with large, durable tires that provide excellent traction on icy surfaces, ensuring stability during operation. The adjustable skid shoes allow users to customize the height of the cutting edge, preventing damage to driveways and walkways.

Furthermore, the Troy-Bilt models boast a two-stage snow throwing system, which is effective in clearing snow of varying depths. This makes them suitable for urban areas with heavy snow accumulation or rural locations where snow drifts can be common.

Overall, the Troy-Bilt 9528 and 7524 snow blowers combine power, durability, and innovative features to deliver outstanding snow removal performance. Whether facing a light dusting or a heavy winter storm, these machines offer reliability and effectiveness, making them an excellent choice for tackling snow with confidence.