Troy-Bilt 7524, 9528 manual Important Safe Operation Practices, Training, Preparation

Page 3

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES

WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.

Training

1.Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

2.Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly.

3.Never allow children under 14 years old to operate this machine. Children 14 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent.

4.Never allow adults to operate this machine without proper instruction.

5.Thrown objects can cause serious personal injury. Plan your snow-throwing pattern to avoid discharge of material toward roads, bystanders and the like.

6.Keep bystanders, helpers, pets and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.

7.Exercise caution to avoid slipping or falling, especially when operating in reverse.

Preparation

1.Thoroughly inspect the area where the equipment is to be used. Remove all doormats, newspapers, sleds, boards, wires and other foreign objects, which could be tripped over or thrown by the auger/ impeller.

2.Always wear safety glasses or eye shields during operation and while performing an adjustment or repair to protect your eyes. Thrown objects which ricochet can cause serious injury to the eyes.

3.Do not operate without wearing adequate winter outer garments. Do not wear jewelry, long scarves or other loose clothing, which could become entangled in moving parts. Wear footwear which will improve footing on slippery surfaces.

4.Use a grounded three-wire extension cord and receptacle for all units with electric start engines.

5.Adjust collector housing height to clear gravel or crushed rock surfaces.

6.Disengage all control levers before starting the engine.

7.Never attempt to make any adjustments while engine is running, except where specifically recommended in the operator’s manual.

8.Let engine and machine adjust to outdoor temperature before starting to clear snow.

9.To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes, which can ignite. Wash your skin and change clothes immediately.

a.Use only an approved gasoline container.

b.Extinguish all cigarettes, cigars, pipes and other sources of ignition.

c.Never fuel machine indoors.

d.Never remove gas cap or add fuel while the engine is hot or running.

e.Allow engine to cool at least two minutes before refueling.

f.Never over fill fuel tank. Fill tank to no more than ½ inch below bottom of filler neck to provide space for fuel expansion.

g.Replace gasoline cap and tighten securely.

h.If gasoline is spilled, wipe it off the engine and equipment. Move machine to another area. Wait 5 minutes before starting the engine.

i.Never store the machine or fuel container inside where there is an open flame, spark or pilot light (e.g. furnace, water heater, space heater, clothes dryer etc.).

j.Allow machine to cool at least 5 minutes before storing.

3

Image 3
Contents Operator’s Manual Table of Contents Important Safe Operation Practices TrainingPreparation Operation Maintenance & StorageDo not modify engine Your ResponsibilityAssembling Your Snow Thrower Tire Pressure Know Your Snow Thrower Drive Control Clean-Out ToolChute Assembly Auger ControlElectric Starter Operating Your Snow ThrowerBefore Starting Gas & Oil Fill-Up Starting The EngineAuger Control Test Stopping The EngineTo Engage Drive To Engage AugersChute Clean-Out Tool Drive / Auger LockOperating Tips Tire Pressure Shift Rod AdjustmentJoy-Stick Cable Adjustment Engine LubricationShave Plate and Skid Shoes Auger Belt Replacement Drive Belt Replacement Friction Wheel Removal OFF-SEASON Storage Trouble Possible Causes Corrective Action Trouble Shooting GuidePage Parts List Style Q 1021 Style Q 12 15 634-04147 15 x 634-04151 734-04012 MANUFACTURER’S Limited Warranty for

7524, 9528 specifications

The Troy-Bilt 9528 and 7524 are popular snow blowers engineered to tackle winter's toughest challenges. With robust features and advanced technologies, these machines are designed for both residential and light commercial use, ensuring efficient snow removal for homeowners and businesses alike.

One of the defining characteristics of these models is their powerful engines. The 9528 is equipped with a 277cc engine, while the 7524 features a 208cc engine. Both engines provide the necessary power to handle heavy snowfall and deliver optimal performance even in the harshest winter conditions. The electric start capability on these models adds convenience, allowing users to start the machines with just the push of a button.

The build quality of the Troy-Bilt 9528 and 7524 is impressive, featuring a durable steel construction that enhances their longevity and reliability. Their rugged auger systems, designed for maximum snow intake, work in tandem with a strong impeller to efficiently throw snow far away from the path, reducing the need for multiple passes.

User-friendly controls are another highlight of these snow blowers. The models come with an easy-to-use dashboard that allows operators to adjust speed and chute direction with minimal effort. The power steering feature on the 9528 facilitates maneuverability, enabling users to navigate tight spots and challenging landscapes with ease.

In addition, both machines are equipped with large, durable tires that provide excellent traction on icy surfaces, ensuring stability during operation. The adjustable skid shoes allow users to customize the height of the cutting edge, preventing damage to driveways and walkways.

Furthermore, the Troy-Bilt models boast a two-stage snow throwing system, which is effective in clearing snow of varying depths. This makes them suitable for urban areas with heavy snow accumulation or rural locations where snow drifts can be common.

Overall, the Troy-Bilt 9528 and 7524 snow blowers combine power, durability, and innovative features to deliver outstanding snow removal performance. Whether facing a light dusting or a heavy winter storm, these machines offer reliability and effectiveness, making them an excellent choice for tackling snow with confidence.