Operation, Maintenance & Storage | Troy-Bilt 9528, 7524 guide

Operation

1.Do not put hands or feet near rotating parts, in the auger/impeller housing or chute assembly. Contact with the rotating parts can amputate hands and feet.

2.The auger/impeller control lever is a safety device. Never bypass its operation. Doing so makes the machine unsafe and may cause personal injury.

3.The control levers must operate easily in both directions and automatically return to the disengaged position when released.

4.Never operate with a missing or damaged chute assembly. Keep all safety devices in place and working.

5.Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

6.Do not operate machine while under the influence of alcohol or drugs.

7.Muffler and engine become hot and can cause a burn. Do not touch.

8.Exercise extreme caution when operating on or crossing gravel surfaces. Stay alert for hidden hazards or traffic.

9.Exercise caution when changing direction and while operating on slopes.

10.Plan your snow-throwing pattern to avoid discharge towards windows, walls, cars etc. Thus, avoiding possible property damage or personal injury caused by a ricochet.

11.Never direct discharge at children, bystanders and pets or allow anyone in front of the machine.

12.Do not overload machine capacity by attempting to clear snow at too fast of a rate.

13.Never operate this machine without good visibility or light. Always be sure of your footing and keep a firm hold on the handles. Walk, never run.

14.Disengage power to the auger/impeller when transporting or not in use.

15.Never operate machine at high transport speeds on slippery surfaces. Look down and behind and use care when backing up.

16.If the machine should start to vibrate abnormally, stop the engine, disconnect the spark plug wire and ground it against the engine. Inspect thoroughly for damage. Repair any damage before starting and operating.

17.Disengage all control levers and stop engine before you leave the operating position (behind the handles). Wait until the auger/impeller comes to a complete stop before unclogging the chute assembly, making any adjustments, or inspections.

18.Never put your hand in the discharge or collector openings. Always use the clean-out tool provided to unclog the discharge opening. Do not unclog chute assembly while engine is running. Shut off engine and remain behind handles until all moving parts have stopped before unclogging.

19.Use only attachments and accessories approved by the manufacturer (e.g. wheel weights, tire chains, cabs etc.).

20.If situations occur which are not covered in this manual, use care and good judgment. Contact your dealer or call (800) 520-5520 for assistance and the name of your nearest servicing dealer.

Maintenance & Storage

1.Never tamper with safety devices. Check their proper operation regularly. Refer to the maintenance and adjustment sections of this manual.

2.Before cleaning, repairing, or inspecting machine disengage all control levers and stop the engine. Wait until the auger/impeller come to a complete stop. Disconnect the spark plug wire and ground against the engine to prevent unintended starting.

3.Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage.

4.Do not change the engine governor setting or over- speed the engine. The governor controls the maximum safe operating speed of the engine.

5.Snow thrower shave plates and skid shoes are subject to wear and damage. For your safety protection, frequently check all components and replace with original equipment manufacturer’s (OEM) parts only. “Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!”

6.Check controls periodically to verify they engage and disengage properly and adjust, if necessary. Refer to the adjustment section in this operator’s manual for instructions.

7.Maintain or replace safety and instruction labels, as necessary.

8.Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment.

9.Prior to storing, run machine a few minutes to clear snow from machine and prevent freeze up of auger/ impeller.

10.Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer etc.

11.Always refer to the operator’s manual for proper instructions on off-season storage.

7524, 9528 specifications

The Troy-Bilt 9528 and 7524 are popular snow blowers engineered to tackle winter's toughest challenges. With robust features and advanced technologies, these machines are designed for both residential and light commercial use, ensuring efficient snow removal for homeowners and businesses alike.

One of the defining characteristics of these models is their powerful engines. The 9528 is equipped with a 277cc engine, while the 7524 features a 208cc engine. Both engines provide the necessary power to handle heavy snowfall and deliver optimal performance even in the harshest winter conditions. The electric start capability on these models adds convenience, allowing users to start the machines with just the push of a button.

The build quality of the Troy-Bilt 9528 and 7524 is impressive, featuring a durable steel construction that enhances their longevity and reliability. Their rugged auger systems, designed for maximum snow intake, work in tandem with a strong impeller to efficiently throw snow far away from the path, reducing the need for multiple passes.

User-friendly controls are another highlight of these snow blowers. The models come with an easy-to-use dashboard that allows operators to adjust speed and chute direction with minimal effort. The power steering feature on the 9528 facilitates maneuverability, enabling users to navigate tight spots and challenging landscapes with ease.

In addition, both machines are equipped with large, durable tires that provide excellent traction on icy surfaces, ensuring stability during operation. The adjustable skid shoes allow users to customize the height of the cutting edge, preventing damage to driveways and walkways.

Furthermore, the Troy-Bilt models boast a two-stage snow throwing system, which is effective in clearing snow of varying depths. This makes them suitable for urban areas with heavy snow accumulation or rural locations where snow drifts can be common.

Overall, the Troy-Bilt 9528 and 7524 snow blowers combine power, durability, and innovative features to deliver outstanding snow removal performance. Whether facing a light dusting or a heavy winter storm, these machines offer reliability and effectiveness, making them an excellent choice for tackling snow with confidence.