Troy-Bilt 1030 manual Electric Starter, Recoil Starter

Page 10

Electric Starter

Before starting, make sure that the engine has suffi- cient oil. The snow thrower engine is equipped with a 120 volt A.C. electric starter and recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 volt AC household current. Follow all instructions carefully.

Cold Start

NOTE: If the unit shows any sign of motion (drive or augers) with the clutch grips disengaged, shut the engine off immediately. Readjust as instructed in the “Final Adjustments” section of the Assembly Instructions.

WARNING: The electric starter must be properly grounded at all times to avoid the possibility of electric shock which may be injurious to the operator.

1.Determine whether your house wiring is a three- wire grounded system. Ask a licensed electrician if you are not certain.

WARNING: If your house wiring system is not a three-wire grounded system, do not use this electric starter under any conditions.

•If your house wiring system is grounded and a three-hole receptacle is not available at the point the snow thrower starter will normally be used, one should be installed by a licensed electrician.

•When connecting the power cord, always connect cord to starter on engine first, then plug the other end into a three-hole grounded receptacle.

•When disconnecting the power cord, always unplug the end from the three-hole, grounded receptacle

first.

2.Attach spark plug wire to spark plug.

3.Turn fuel valve on, if so equipped.

4.Make sure that the auger and drive controls are in the disengaged (up) position.

5.Move throttle control lever to FAST position.

6.Push key into the ignition slot and snap in place. Do not turn key.

7.Connect power cord to switch box on the engine.

8.Plug the other end of the power cord into a three- hole, grounded 120 volt A.C. receptacle.

9.Rotate choke knob to FULL choke position (cold engine start). If engine is warm, place choke in OFF position instead of FULL.

10.Push the primer three times.

11.Push down on the starter button until the engine starts. Do not crank for more than 10 seconds at a time. This electric starter is thermally protected. If overheated, it will stop automatically and can be restarted only when it has cooled to a safe temperature (a wait of 5 -10 minutes is required).

12.When the engine starts, release the starter button and slowly rotate the choke to OFF position. If the engine falters, rotate the choke to FULL and then gradually to OFF.

13.Disconnect the power cord from the receptacle first and then from the switch box on the engine.

14.Allow the engine to warm up for a few minutes because the engine will not develop full power until it reaches operating temperature. Operate the engine at full throttle (FAST) when throwing snow.

Recoil Starter

Make sure that the engine has sufficient oil and the auger and drive controls are released.

Cold Start

1.Move throttle control to FAST position.

2.Turn fuel valve on, if so equipped.

3.Push key into the ignition slot and snap in place. Do not turn key.

4.Rotate choke control to FULL choke position.

5.Push the primer button while covering the vent hole. Remove your finger from the primer between primes. Do not prime if temperature is above 50o F; prime two times between 50o F and 15o F; and prime four times below 15o F.

6.Pull the starter handle rapidly. Do not allow the handle to snap back, but allow it to rewind slowly while keeping a firm hold on the starter handle.

7.As the engine warms up, rotate the choke knob slowly to OFF position. If the engine falters, return to FULL choke, then slowly move to OFF choke position.

8.Allow the engine to warm up for a few minutes because the engine will not develop full power until it reaches operating temperature.

9.Operate the engine at full throttle (FAST) when throwing snow.

Warm Start

1.If restarting a warm engine after a temporary shut down, rotate choke to OFF instead of FULL and do not prime. Pull starter handle as instructed earlier.

Frozen Recoil Starter

If the starter is frozen and will not turn the engine, proceed as follows:

1.Pull as much rope out of the starter as possible.

2.Release the starter handle and let it snap back against the starter.

3.If the engine still fails to start, repeat the first two steps. If continued attempts do not free starter, follow the electric starter procedures to start.

4.Avoid freezing of the recoil starter by following instructions below.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s Manual Table of Contents Important Safe Operations Practices TrainingOperation Setting up the Snow Thrower Setting UP Your Snow ThrowerBefore Assembly Removing From CartonAuger Control Test Final AdjustmentsDrive Control & Shift Lever Tire Pressure Pneumatic Tires Shear Pin StorageSkid Shoe Four-Way Chute ControlDrive Control/ Auger Control Lock Operating Your Snow ThrowerKnow The Controls Auger ControlBefore Starting Engine To Start EngineElectric Starter Recoil StarterTo Engage Drive Before StoppingTo Stop The Snow Thrower To Engage AugersMaintaining Your Snow Thrower Chute Clean-Out ToolGeneral Recommendations Check Chute Cables Check V-BeltsCheck Friction Wheel Checking Oil LevelShave Plate and Skid Shoes Service & AdjustmentServicing Augers Replacing BeltAuger Belt Drive BeltFriction Wheel Rubber Drive Control AdjustmentsShift Rod Preparing For Storage Chute ControlTroubleshooting Parts List for Model Model Model Handle Engagement Assembly RH Cable Z- Fitting 731-04894 42C 43A 41A 42A 42H 41B 42I 43D 43B 42B 42J Ref No. Part No Description Safety & Decorative Labels MANUFACTURER’S Limited Commercial Warranty For MANUFACTURER’S Limited Warranty for

1030 specifications

The Troy-Bilt 1030 is a powerful and versatile snow blower designed to tackle the toughest winter conditions. With its robust construction and innovative features, it stands out as a reliable choice for homeowners who need to clear snow from large driveways and walkways.

One of the main features of the Troy-Bilt 1030 is its 2-stage snow removal system. This system utilizes an auger to collect the snow and a powerful impeller to propel it out through the discharge chute. This dual mechanism allows for efficient snow clearing, making it capable of handling heavy and compacted snow. With a clearing width of 30 inches and a depth of up to 23 inches, the Troy-Bilt 1030 can significantly reduce the time and effort needed to clear extensive areas.

Equipped with a robust 10.5 HP engine, the Troy-Bilt 1030 provides ample power to manage various snow conditions, including ice and slush. Its recoil start and electric start option offer convenience, allowing users to start the machine effortlessly even in the coldest temperatures. The snow blower’s adjustable speed transmission features six forward and two reverse speeds, allowing for smooth operation and flexibility while navigating various terrains.

Another standout feature is the 200-degree adjustable chute, which gives users the control needed to direct snow precisely where it needs to go. This feature minimizes the chances of snow being blown back onto the cleared area, enhancing overall efficiency. The chute also features a quick-release mechanism that allows for easy adjustments on the go.

The Troy-Bilt 1030 is built with user comfort in mind, featuring ergonomic hand grips and easy-to-reach controls, ensuring a comfortable experience even during prolonged use. Its durable construction, complete with a reinforced steel frame and housing, provides long-lasting performance season after season.

Safety is prioritized with features like the safety key, which prevents accidental starts, and the in-dash headlight, enhancing visibility during early morning or late evening snow removal. For added peace of mind, the Troy-Bilt 1030 comes with a warranty, reflecting the manufacturer’s commitment to quality and reliability.

In summary, the Troy-Bilt 1030 is ideal for homeowners looking for a sturdy, efficient snow blower capable of handling heavy snowfall. With its powerful engine, advanced features, and user-friendly design, it makes winter maintenance more manageable and less time-consuming. This snow blower is a smart investment for anyone living in areas prone to heavy winter weather, ensuring that you can keep your property safe and accessible all season long.
Top Page Image Contents