Troy-Bilt 1030 manual Adjustments, Drive Control, Shift Rod

Page 17

10.Insert the shift arm assembly into the friction wheel assembly and hold assembly in position. See Figure 22.

11.Slide hex gear shaft through right side of the housing and the friction wheel assembly.

12.Insert the hex gear shaft through the sprocket and the spacer. Make certain that chain engages both the large and the small sprocket.

NOTE: If the sprocket fell from the snow thrower while removing the hex gear shaft, place the sprocket on the hex gear shaft. Position the hex hub of the sprocket toward the friction wheel when sliding the sprocket on to hex gear shaft.

13.Align the hex gear shaft with the left bearing and carefully guide this bearing into left side of housing.

14.Install the right bearing on the hex gear shaft and check that the spacer and bearing in the drive cover are aligned to the steerable shaft. See Figure 22.

Shift

Friction

Arm

 

Wheel

 

Hex

 

Gear Shaft

Figure 22

15.Reassemble the drive cover with four screws removed in step 6. Install the right wheel with the bolt removed earlier.

16.Reassemble the frame cover with the self-tapping screws. Flip the equipment back to the operating position and re-attach the belt cover.

NOTE: If you placed plastic under the gas cap, be certain to remove it.

Adjustments

Drive Control

Refer to the Final Adjustment section of the Assembly instructions to adjust the drive control. To check the adjustment, proceed as follows:

1.With the snow thrower tipped forward (be certain to drain the gasoline or place plastic film under the gas cap if the snow thrower has already been operated), remove the frame cover underneath the snow thrower by removing the self-tapping screws.

2.With the drive control released, there must be 1/8” clearance between the friction wheel and the drive plate in all positions of the shift lever.

3.With the drive control engaged, the friction wheel must contact the drive plate (Figure 19).

4.If adjustment is necessary, loosen the jam nut on the drive cable and thread the cable in or out as necessary. Tighten the jam nut to secure the cable when correct adjustment is reached. Reassemble the frame cover.

NOTE: If you placed plastic under the gas cap, be certain to remove it.

Auger Control

Refer to page 6 for details.

.

Shift Rod

To adjust the shift rod, proceed as follows.

1.Place shift lever in sixth (6) position or the fastest forward speed. See Figure 23A.

A

Shift

B

 

Lever

 

 

Hairpin Clip

 

 

Ferrule

 

 

Shift

 

 

Rod

C

 

 

 

 

Shift Arm

Figure 23

2.Remove hairpin clip from the shift handle under the handle panel. See Figure 23B.

3.Push shift arm assembly down as far as it will go. See Figure 23C.

4.Rotate the ferrule up or down the shift rod as necessary until the ferrule lines up with the upper hole in the shift lever. See Figure 23B.

5.Insert ferrule from right side of the snow thrower into the upper hole in shift lever. See Figure 23B.

6.Reinstall the hairpin clip.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Operator’s Manual Table of Contents Training Important Safe Operations PracticesOperation Before Assembly Setting UP Your Snow ThrowerSetting up the Snow Thrower Removing From CartonDrive Control & Shift Lever Final AdjustmentsAuger Control Test Skid Shoe Shear Pin StorageTire Pressure Pneumatic Tires Four-Way Chute ControlKnow The Controls Operating Your Snow ThrowerDrive Control/ Auger Control Lock Auger ControlTo Start Engine Before Starting EngineRecoil Starter Electric StarterTo Stop The Snow Thrower Before StoppingTo Engage Drive To Engage AugersGeneral Recommendations Chute Clean-Out ToolMaintaining Your Snow Thrower Check Friction Wheel Check V-BeltsCheck Chute Cables Checking Oil LevelServicing Augers Service & AdjustmentShave Plate and Skid Shoes Replacing BeltDrive Belt Auger BeltFriction Wheel Rubber Shift Rod AdjustmentsDrive Control Chute Control Preparing For StorageTroubleshooting Parts List for Model Model Model Handle Engagement Assembly RH Cable Z- Fitting 731-04894 42C 43A 41A 42A 42H 41B 42I 43D 43B 42B 42J Ref No. Part No Description Safety & Decorative Labels MANUFACTURER’S Limited Commercial Warranty For MANUFACTURER’S Limited Warranty for

1030 specifications

The Troy-Bilt 1030 is a powerful and versatile snow blower designed to tackle the toughest winter conditions. With its robust construction and innovative features, it stands out as a reliable choice for homeowners who need to clear snow from large driveways and walkways.

One of the main features of the Troy-Bilt 1030 is its 2-stage snow removal system. This system utilizes an auger to collect the snow and a powerful impeller to propel it out through the discharge chute. This dual mechanism allows for efficient snow clearing, making it capable of handling heavy and compacted snow. With a clearing width of 30 inches and a depth of up to 23 inches, the Troy-Bilt 1030 can significantly reduce the time and effort needed to clear extensive areas.

Equipped with a robust 10.5 HP engine, the Troy-Bilt 1030 provides ample power to manage various snow conditions, including ice and slush. Its recoil start and electric start option offer convenience, allowing users to start the machine effortlessly even in the coldest temperatures. The snow blower’s adjustable speed transmission features six forward and two reverse speeds, allowing for smooth operation and flexibility while navigating various terrains.

Another standout feature is the 200-degree adjustable chute, which gives users the control needed to direct snow precisely where it needs to go. This feature minimizes the chances of snow being blown back onto the cleared area, enhancing overall efficiency. The chute also features a quick-release mechanism that allows for easy adjustments on the go.

The Troy-Bilt 1030 is built with user comfort in mind, featuring ergonomic hand grips and easy-to-reach controls, ensuring a comfortable experience even during prolonged use. Its durable construction, complete with a reinforced steel frame and housing, provides long-lasting performance season after season.

Safety is prioritized with features like the safety key, which prevents accidental starts, and the in-dash headlight, enhancing visibility during early morning or late evening snow removal. For added peace of mind, the Troy-Bilt 1030 comes with a warranty, reflecting the manufacturer’s commitment to quality and reliability.

In summary, the Troy-Bilt 1030 is ideal for homeowners looking for a sturdy, efficient snow blower capable of handling heavy snowfall. With its powerful engine, advanced features, and user-friendly design, it makes winter maintenance more manageable and less time-consuming. This snow blower is a smart investment for anyone living in areas prone to heavy winter weather, ensuring that you can keep your property safe and accessible all season long.
Top Page Image Contents