Troy-Bilt 1030 Service & Adjustment, Servicing Augers, Shave Plate and Skid Shoes, Replacing Belt

Page 14

SECTION 4: SERVICE & ADJUSTMENT

WARNING: Always stop engine, disconnect spark plug wire and move it away from spark plug before performing adjustments or repairs. Always wear safety glasses during operation or while performing any adjustments or repairs.

Servicing Augers

The augers are secured to the spiral shaft with six shear pins and cotter pins. See Figure 12 .

1.If the augers do not turn, check to see if the pins have sheared.

2.Replace the pins if needed. Two replacement shear pins and cotter pins have been provided with the snow thrower. Spray an oil lubricant into shaft before inserting new pins and securing with new cotter pins. See Figure 12.

Auger

Shear

Pin

Cotter Pin

Figure 12

IMPORTANT: NEVER replace the auger shear pins with standard pins. Any damage to the auger gearbox or other components, as a result of doing so, will NOT be covered by your snow thrower’s warranty.

Shave Plate and Skid Shoes

The shave plate and skid shoes at the bottom of the snow thrower are subject to wear. Check these periodically and replace as necessary.

Replacing Skid Shoe

1.Remove the four carriage bolts and lock nuts which attach the two skid shoes to the snow thrower on two sides. See Figure 13 .

Carriage Bolt

Skid

Shoe

Shave Plate

Lock Nut

Nut

Figure 13

2.Reassemble new skid shoes with the same hardware. Make certain the skid shoes are adjusted to be level.

Replacing Shave Plate

1.After removing both skid shoes, remove four carriage bolts and lock nuts which attach shave plate to the snow thrower housing. See Figure 13 . The shave plate and skid shoes at the bottom of the snow thrower are subject to wear. Check these periodically and replace as necessary.

2.Reassemble new shave plate, making sure heads of the carriage bolts are to the inside of the housing. Tighten securely. Re-install skid shoes.

Replacing Belt

Check the condition of both auger belt and drive belt every 25 hours of snow thrower operation. Replace if either shows signs of wear and tear. To remove and replace either the auger belt or the drive belt, follow the steps below and then proceed to the specific steps listed under respective sub-headings.

1.Remove belt cover by removing the two self- tapping screws that secure it to the snow thrower housing. See Figure 14A.

2.Take auger belt off the pulley following Figure 14B.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operator’s Manual Table of Contents Important Safe Operations Practices TrainingOperation Setting up the Snow Thrower Setting UP Your Snow ThrowerBefore Assembly Removing From CartonDrive Control & Shift Lever Final AdjustmentsAuger Control Test Tire Pressure Pneumatic Tires Shear Pin StorageSkid Shoe Four-Way Chute ControlDrive Control/ Auger Control Lock Operating Your Snow ThrowerKnow The Controls Auger ControlBefore Starting Engine To Start EngineElectric Starter Recoil StarterTo Engage Drive Before StoppingTo Stop The Snow Thrower To Engage AugersGeneral Recommendations Chute Clean-Out ToolMaintaining Your Snow Thrower Check Chute Cables Check V-BeltsCheck Friction Wheel Checking Oil LevelShave Plate and Skid Shoes Service & AdjustmentServicing Augers Replacing BeltAuger Belt Drive BeltFriction Wheel Rubber Shift Rod AdjustmentsDrive Control Preparing For Storage Chute ControlTroubleshooting Parts List for Model Model Model Handle Engagement Assembly RH Cable Z- Fitting 731-04894 42C 43A 41A 42A 42H 41B 42I 43D 43B 42B 42J Ref No. Part No Description Safety & Decorative Labels MANUFACTURER’S Limited Commercial Warranty For MANUFACTURER’S Limited Warranty for

1030 specifications

The Troy-Bilt 1030 is a powerful and versatile snow blower designed to tackle the toughest winter conditions. With its robust construction and innovative features, it stands out as a reliable choice for homeowners who need to clear snow from large driveways and walkways.

One of the main features of the Troy-Bilt 1030 is its 2-stage snow removal system. This system utilizes an auger to collect the snow and a powerful impeller to propel it out through the discharge chute. This dual mechanism allows for efficient snow clearing, making it capable of handling heavy and compacted snow. With a clearing width of 30 inches and a depth of up to 23 inches, the Troy-Bilt 1030 can significantly reduce the time and effort needed to clear extensive areas.

Equipped with a robust 10.5 HP engine, the Troy-Bilt 1030 provides ample power to manage various snow conditions, including ice and slush. Its recoil start and electric start option offer convenience, allowing users to start the machine effortlessly even in the coldest temperatures. The snow blower’s adjustable speed transmission features six forward and two reverse speeds, allowing for smooth operation and flexibility while navigating various terrains.

Another standout feature is the 200-degree adjustable chute, which gives users the control needed to direct snow precisely where it needs to go. This feature minimizes the chances of snow being blown back onto the cleared area, enhancing overall efficiency. The chute also features a quick-release mechanism that allows for easy adjustments on the go.

The Troy-Bilt 1030 is built with user comfort in mind, featuring ergonomic hand grips and easy-to-reach controls, ensuring a comfortable experience even during prolonged use. Its durable construction, complete with a reinforced steel frame and housing, provides long-lasting performance season after season.

Safety is prioritized with features like the safety key, which prevents accidental starts, and the in-dash headlight, enhancing visibility during early morning or late evening snow removal. For added peace of mind, the Troy-Bilt 1030 comes with a warranty, reflecting the manufacturer’s commitment to quality and reliability.

In summary, the Troy-Bilt 1030 is ideal for homeowners looking for a sturdy, efficient snow blower capable of handling heavy snowfall. With its powerful engine, advanced features, and user-friendly design, it makes winter maintenance more manageable and less time-consuming. This snow blower is a smart investment for anyone living in areas prone to heavy winter weather, ensuring that you can keep your property safe and accessible all season long.
Top Page Image Contents