Troy-Bilt 1030 manual Friction Wheel Rubber

Page 16

4.Back out the stop bolt to create sufficient gap between the friction wheel disc and the drive pulley. Pull the drive belt from around the drive pulley and clear it off the friction wheel disc. See Figure 18.

Drive

Friction

Belt

Wheel

 

Drive Pulley

Stop

 

Bolt

 

Figure 18

5.Now moving to the other side of the snow thrower again, slide the belt off the crankshaft.

6.Replace with new belt, first sliding it through the crank shaft, then working it around the groove of the drive pulley and finally wrapping it around the engine pulley from where the old belt was removed. Once the belt is firmly placed on the pulleys, make sure to remove the screwdriver from the idler.

7.Re-install auger belt on the engine pulley.

8.Re-attach frame cover on the snow thrower housing and put the equipment back to operating position. Re-attach belt cover with two self-tapping screws removed earlier.

Friction Wheel Rubber

1.Check the rubber on the friction wheel after 25 hours of operation, and periodically thereafter. Replace the rubber if any signs of wear or cracking are found.

2.Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap. Move shift lever to the R2 position.

3.Tip the snow thrower so that it rests on the housing. Remove the self-tapping screws from the frame cover underneath the snow thrower.

4.Remove bolt securing the right wheel, and remove the wheel from the axle.

5.Remove the four screws securing the right drive cover to the frame. Remove the drive cover from the side of the frame. See Figure 19.

Drive Cover

Bolt

Spacer

Figure 19

6.Holding the friction wheel assembly, slide the hex gear shaft to the right. See Figure 20. The spacer on right side of hex gear shaft may fall.

Bearing

Sprocket

Figure 20

7.Lift the friction wheel assembly out between the axle shaft and the drive shaft assemblies.

8.Remove the four screws from the friction wheel assembly. Remove friction wheel rubber from between the friction wheel plate. See Figure 21.

 

Plate

Friction

Screw

Wheel

Rubber

Figure 21

9.Reassemble new friction wheel rubber to the friction wheel assembly, tightening the four screws in rotation and with equal force. See Figure 21.

IMPORTANT: Assemble the rubber on the friction wheel equally for proper functioning.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Operator’s Manual Table of Contents Important Safe Operations Practices TrainingOperation Setting UP Your Snow Thrower Before AssemblySetting up the Snow Thrower Removing From CartonAuger Control Test Final AdjustmentsDrive Control & Shift Lever Shear Pin Storage Skid ShoeTire Pressure Pneumatic Tires Four-Way Chute ControlOperating Your Snow Thrower Know The ControlsDrive Control/ Auger Control Lock Auger ControlBefore Starting Engine To Start EngineElectric Starter Recoil StarterBefore Stopping To Stop The Snow ThrowerTo Engage Drive To Engage AugersMaintaining Your Snow Thrower Chute Clean-Out ToolGeneral Recommendations Check V-Belts Check Friction WheelCheck Chute Cables Checking Oil LevelService & Adjustment Servicing AugersShave Plate and Skid Shoes Replacing BeltAuger Belt Drive BeltFriction Wheel Rubber Drive Control AdjustmentsShift Rod Preparing For Storage Chute ControlTroubleshooting Parts List for Model Model Model Handle Engagement Assembly RH Cable Z- Fitting 731-04894 42C 43A 41A 42A 42H 41B 42I 43D 43B 42B 42J Ref No. Part No Description Safety & Decorative Labels MANUFACTURER’S Limited Commercial Warranty For MANUFACTURER’S Limited Warranty for

1030 specifications

The Troy-Bilt 1030 is a powerful and versatile snow blower designed to tackle the toughest winter conditions. With its robust construction and innovative features, it stands out as a reliable choice for homeowners who need to clear snow from large driveways and walkways.

One of the main features of the Troy-Bilt 1030 is its 2-stage snow removal system. This system utilizes an auger to collect the snow and a powerful impeller to propel it out through the discharge chute. This dual mechanism allows for efficient snow clearing, making it capable of handling heavy and compacted snow. With a clearing width of 30 inches and a depth of up to 23 inches, the Troy-Bilt 1030 can significantly reduce the time and effort needed to clear extensive areas.

Equipped with a robust 10.5 HP engine, the Troy-Bilt 1030 provides ample power to manage various snow conditions, including ice and slush. Its recoil start and electric start option offer convenience, allowing users to start the machine effortlessly even in the coldest temperatures. The snow blower’s adjustable speed transmission features six forward and two reverse speeds, allowing for smooth operation and flexibility while navigating various terrains.

Another standout feature is the 200-degree adjustable chute, which gives users the control needed to direct snow precisely where it needs to go. This feature minimizes the chances of snow being blown back onto the cleared area, enhancing overall efficiency. The chute also features a quick-release mechanism that allows for easy adjustments on the go.

The Troy-Bilt 1030 is built with user comfort in mind, featuring ergonomic hand grips and easy-to-reach controls, ensuring a comfortable experience even during prolonged use. Its durable construction, complete with a reinforced steel frame and housing, provides long-lasting performance season after season.

Safety is prioritized with features like the safety key, which prevents accidental starts, and the in-dash headlight, enhancing visibility during early morning or late evening snow removal. For added peace of mind, the Troy-Bilt 1030 comes with a warranty, reflecting the manufacturer’s commitment to quality and reliability.

In summary, the Troy-Bilt 1030 is ideal for homeowners looking for a sturdy, efficient snow blower capable of handling heavy snowfall. With its powerful engine, advanced features, and user-friendly design, it makes winter maintenance more manageable and less time-consuming. This snow blower is a smart investment for anyone living in areas prone to heavy winter weather, ensuring that you can keep your property safe and accessible all season long.
Top Page Image Contents