Yard-Man 5KL manual Final Adjustments, Auger Control Test, Drive Control & Shift Lever

Page 6

7.Insert the round end of the chute control box on the short tube of the chute assembly as shown in Figure 3C.

8.Insert other end of the chute control box into the chute support tube as shown in Figure 3C.

9.Insert the clevis pin, earlier removed, through the holes on the chute control box and chute support rod. Secure with the hairpin clip. See Figure 3D.

10.Slip the cables, running from the handle panel to the chute, into the cable guide located on top of the engine. See Figure 4 .

11.Slip the cables, running from the handle panel to the chute control box, into the cable guide too. See Figure 4.

Cable Guide

Chute

Assembly

Figure 4

12.The extension cord is fastened with a cable tie to the rear of the auger housing for shipping purposes. Cut the cable tie and remove it before operating the snow thrower.

Final Adjustments

After setting up your snow thrower, check the adjustments as instructed below and make any final adjustments necessary before operating the unit.

CAUTION: Perform the following test before operating the snow thrower for the first time and at the start of each winter season. Failure to comply with these adjustment instructions may cause damage to the unit.

Auger Control Test

1.To check the adjustment of the auger control, push forward the left hand control until the rubber bumper is compressed. There should be slack in the cable.

2.Release the control. The cable should be straight. Make certain you can depress the auger control against the left handle completely.

WARNING: Do not over-tighten the cable. Over-tightening may prevent the auger from disengaging and compromise the safety of the snow thrower.

3.In a well-ventilated area, start the snow thrower engine as instructed earlier in this section under the heading Starting Engine. Make sure the throttle is set in the FAST position.

4.While standing in the operator’s position (behind the snow thrower) engage the auger.

5.Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times.

6.With the engine running in the FAST position and the auger control in the disengaged “up” position, walk to the front of the machine.

7.Confirm that the auger has completely stopped rotating and shows NO signs of motion.

IMPORTANT: If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for all moving parts to stop before readjusting the auger control cable.

8.If adjustment is necessary, loosen the jam nut and thread the cable in (for less slack) or out (for more slack). See Figure 5.

9.Recheck the adjustment. Tighten jam nut against the cable when correct adjustment is reached.

Auger

Jam

Nut

Cable

 

Figure 5

Drive Control & Shift Lever

1.Tip the snow thrower forward so that it rests on the auger housing.

2.Move the shift lever all the way forward to the sixth

(6) position.

3.With the drive control released, spin the snow thrower wheels by hand. The wheels should turn; however, you may feel some resistance.

4.Engage the drive control. The wheels should no longer turn.

5.Now release the drive control and spin the wheels again.

6.Move the shift lever back to the fast reverse position and then all the way forward again. There should be no resistance in the shift lever and the wheels should turn.

7.If you face resistance when moving the shift lever or the wheels stop when they should not, loosen the jam nut on the drive cable and unthread the cable one turn.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Operator’s Manual Table of Contents Important Safe Operations Practices TrainingOperation Setting up the Snow Thrower Setting UP Your Snow ThrowerBefore Assembly Removing From CartonFinal Adjustments Auger Control TestDrive Control & Shift Lever Skid Shoe Tire Pressure Pneumatic TiresFour-Way Chute Control Drive Control/ Auger Control Lock Operating Your Snow ThrowerKnow The Controls Auger ControlBefore Starting Engine To Start EngineBefore Stopping Recoil StarterTo Engage Drive Chute Clean-Out ToolTo Stop The Snow Thrower To Engage AugersMaintaining Your Snow Thrower General RecommendationsCheck Chute Cables Check V-BeltsCheck Friction Wheel Checking Oil LevelShave Plate and Skid Shoes Service & AdjustmentServicing Augers Replacing BeltAuger Belt Drive BeltFriction Wheel Rubber Adjustments Drive ControlShift Rod Preparing For Storage Chute ControlTroubleshooting Parts List for Model 5KL Model 5KL 4211 Handle Engagement Assembly RH Cable Z- Fitting 731-04894 41A 42C 43A 42A 42H 41B 42I 43D 42B 42J Ref No. Part No Description Safety & Decorative Labels Page MANUFACTURER’S Limited Warranty for

5KL specifications

The Yard-Man 5KL is a standout lawn tractor designed for delivering exceptional performance in residential landscaping tasks. Built for efficiency and ease of use, the Yard-Man 5KL is ideal for homeowners with medium to large yards, offering top-notch features and cutting-edge technologies.

One of the defining characteristics of the Yard-Man 5KL is its powerful engine. Equipped with a robust 24 horsepower engine, the tractor provides ample power for a variety of mowing conditions. The engine is designed for reliability, ensuring that it runs smoothly and efficiently during prolonged use. Its advanced air filtration system helps to prolong the life of the engine by keeping it clean and reducing wear and tear.

The Yard-Man 5KL features a 54-inch cutting deck, allowing users to cover a large area in a shorter amount of time. This wide cutting deck is complemented by adjustable cutting height settings, giving users the flexibility to achieve their desired lawn appearance. With simple controls, users can easily switch between different cutting heights, making it versatile for different grass types and conditions.

Comfort is another important aspect of the Yard-Man 5KL. It boasts a spacious, ergonomic seat that is designed to reduce fatigue during extended mowing sessions. The operator's controls are intuitively placed, making it easy to navigate the tractor with minimal distraction. The inclusion of a steering wheel with a tight turning radius enhances maneuverability, allowing users to navigate tight corners and landscaping features seamlessly.

Technology in the Yard-Man 5KL is also noteworthy. The tractor is equipped with automatic transmission, which enables smooth speed adjustments reflective of the mowing conditions without the need for constant shifting. This results in a more relaxed mowing experience. Additionally, the integrated LED headlights offer visibility during early morning or evening mowing sessions.

Durability is a hallmark of the Yard-Man 5KL, as it is constructed with high-quality materials designed for long-lasting performance. The reinforced chassis ensures stability, while rust-resistant components enhance the tractor's longevity. Maintenance is straightforward, with easy access to key components for routine service.

In summary, the Yard-Man 5KL is an exceptional lawn tractor that combines power, comfort, and advanced technology. With its large cutting deck, ergonomic design, and user-friendly features, it serves as a reliable tool for efficient lawn care. Whether tackling large grass areas or navigating tight spaces, the Yard-Man 5KL ensures that homeowners can achieve a well-maintained lawn with ease.
Top Page Image Contents