Cub Cadet WE 26 warranty Skid Shoes, Auger Control

Page 13

You can also check the adjustment as follows:

 

5

1.

With the snow thrower tipped forward (be certain to

 

 

drain gasoline or place plastic film under the gas cap if

 

 

the snow thrower has already been operated), remove

 

 

the frame cover underneath the snow thrower by

 

 

removing the self-tapping screws. Refer to Figure 22

 

 

in Maintenance section.

 

Making

2.

With the drive control released, there must be 1/8"

 

 

Adjustments

 

clearance between the friction wheel and the drive

 

 

pulley in all positions of the shift lever.

 

 

3.

With the drive control engaged, the friction wheel

 

 

 

must contact the drive pulley. Refer to Figure 24 in

 

 

 

Maintenance section.

 

 

4.

If adjustment is necessary, loosen the lower hex nut

 

 

 

on the drive cable index bracket and pivot the bracket

 

 

 

upward or downward as necessary. Refer to Figure

 

 

 

16. Tighten the lower hex nut to secure the bracket

Figure 17

 

 

when correct adjustment is reached.

IMPORTANT: It is not

 

 

5.

Reassemble the frame cover and turn the unit back to

 

recommended that you

 

operate this snow thrower

 

its operating position.

 

 

 

on gravel as loose gravel

 

 

 

NOTE: If you placed plastic under the gas cap, be certain

 

can be easily picked up

 

and thrown by the auger

to remove it now.

 

 

causing personal injury

 

Skid Shoes

 

 

 

or damage to the snow

The space between this shave plate and the ground can

 

thrower.

 

 

be adjusted. For close snow removal, place skid shoes in

 

 

the low position. Use middle or high position when area to

 

If for some reason, you

be cleared is uneven.

 

have to operate the snow

1.

Adjust skid shoes by loosening the four hex nuts,

 

thrower on gravel, keep

 

washers, and carriage bolts and moving skid shoes to

 

the skid shoe in the high-

 

desired position. See Figure 17.

 

est position for maximum

2.

Make certain the entire bottom surface of skid shoes

 

clearance between the

 

ground and the shave

 

are against the ground to avoid uneven wear on the

 

 

 

plate.

 

skid shoes.

 

 

 

 

3.

Tighten nuts and bolts securely.

 

 

Auger Control

To adjust the auger control, refer to the section in this manual titled “Operating Your Snow Thrower”.

13

Image 13
Contents Two-Stage Snow Thrower Model WE OPERATOR’S ManualFinding and Recording Model Number Table of ContentsCustomer Support Your Responsibility Safety LabelsYour Responsibility Restrict the use PracticesYour Responsibility Do not modify engineTighten hand knobs securing upper handle to lower handle Setting Up Your Snow ThrowerShear Pin Storage Chute Clean-Out ToolTire Pressure Know Your Snow Thrower Operating Your Snow ThrowerAuger Control Clean-Out ToolDrive Control/ Auger Control Lock Ignition KeyStopping The Engine Gas & Oil Fill-UpStarting The Engine Electric StarterTo Engage Augers To Engage DriveAuger Control Test Shift Cable Making AdjustmentsChute Control Drive Control Shift LeverAuger Control Skid ShoesEngine Maintaining Your Snow ThrowerLubrication Shave Plate and Skid ShoesAuger Belt Replacement Augers Drive Belt ReplacementFriction Wheel Removal Preparing Engine Off-Season StoragePreparing Snow Thrower Short-Term StorageTrouble- shooting This section Addresses minor Service issuesModel WE26 To order replacement Parts ListOr visit Parts, call the Customer Dealer Referral Line atModel WE26 738-04194 Flange Shoulder Screw 452 26 13 684-04153 Page U.S.A Canada MANUFACTURER’S Limited Commercial Warranty forMANUFACTURER’S Limited Warranty for